This patch enables Trusted Boot on the i.MX8MP with BL2 doing image
verification from a FIP prior to hand-over to BL31.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: Iac1d1d62ea9858f67326a47c1e5ba377f23f9db5
Adds bl2 with FIP to the build required for mbed Linux booting where
we do:
BootROM -> SPL -> BL2 -> OPTEE -> u-boot
If NEED_BL2 is specified then BL2 will be built and BL31 will have its
address range modified upwards to accommodate. BL31 must be loaded from a
FIP in this case.
If NEED_BL2 is not specified then the current BL31 boot flow is unaffected
and u-boot SPL will load and execute BL31 directly.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I78914d6002755f733ea866127cb47982a00f9700
This commit makes the image load logic from imx8mm common for all
imx8m platform.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: Ibfe2e9cc09d198cb9e309afaf381a0237a4b82ed
Adds a number of definitions consistent with the established RSB3720
equivalents specifying number of io_handles and block devices.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I401e48216d67257137351ee4d0b98904a76fa789
This commit makes imx image io-storage logic common for all
imx platform.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I15045ac8f9dfa8cb714e32f9e7475d5eae4e86e4
Allows for exporting of FIP related methods cleanly in a private header.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: Iaaad4e69ef89c8a8a74648647d7fd09cd0fdd12a
In the SCMI power domain off handling, configure GIC
to prevent interrupt toward to the core to be turned off,
and configure CCN to disable coherency when the cluster is turned off.
The same operation is done in SCPI power domain off processing.
This commit adds the missing operation in SCMI power domain
off handling.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: Ib3523de488500c2e8bdc74e4cb8772a1442d9781
In case the WDT is enabled by prior stage, keep it enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ie7c0eaf2f59dd8c30a9ef686a7000424f38d6352
Because the Realtime module stop control register n (RMSTPCRn)
are not supported in R-Car D3. Therefore, remove access to these
registers in R-Car D3.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I4647e28d0e176ff97151e9842019ba12cefe5c03
- Added the condition where output the SSCG (MD12) setting
to log for R-Car D3.
- Added the process to switching the bit rate of SCIF by the
SSCG (MD12) setting value for R-Car D3.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Iaf07fa4df12dc233af0b57569ee4fa9329f670a9
Because the x6 and x7 registers will be overwritten by the callee function,
added the processing the register's value push to/pop from stack memory.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I5351a008d3b208a30a8bc8651b8d9b4d1a02a8e8
Added the process of SYSECEXTMASK bit set/clear for following
power Resume/Shutoff flow.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I71ed22840a42e7ab7d87bfd4241eec6f5ddb129b
The memory area size of OP-TEE was changed from 1MB to 2MB
because the size of OP-TEE has increased.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Ic8a165c83a3a9ef2829f68d5fabeed9ccb6da95e
The new M3 DRAM size can be determined by the PRR cut version.
Read the PRR cut version, and if it is older than cut 30, use
legacy DRAM size scheme, else report 8GB in 2GBx4 2ch split.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> # Fix DRAM size judgment by PRR register, reword commit message
Change-Id: Ib83176d0d09cab5cae0119ba462e42c66c642798
Fix to support of booting from eMMC (50MHz x 8) on
Draak board for R-Car D3.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I0ab2b5c7f8075acbf5f4a69694fb535dddc1a4c8
Added the process of judgment and logging for R-Car D3 Ver.1.1 and Ver.1.0.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I326aa42374b70b6a4a71893561a7eaa0b6eddef0
Changed the plat/renesas/common/common.mk to change the source files
about GICv2 by include gicv2.mk, because gic_common.c has deprecated.
Signed-off-by: Hideyuki Nitta <hideyuki.nitta.jf@hitachi.com>
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Iaa7eae6b2c1dd79a05339325e6bc422d87bce49e
Erratum 1530924 affects Armada 37xx CPU, since it affects all Cortex-A53
revisions from r0p0 to r0p4.
Enable the workaround for this erratum.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I753225040e49e956788d5617cd7ce76d5e6ea8e8
BL2 passes FW_CONFIG to BL31 which contains information
about different DTBs present. BL31 then uses FW_CONFIG
to get the base address of HW_CONFIG and populate fconf.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I0b4fc83e6e0a0b9401f692516654eb9a3b037616
This avoids duplicate define of TZC_REGION_NSEC_ALL_ACCESS_RDWR.
And remove the previous TZC400 definitions from stm32mp1_def.h.
Change-Id: I6c72c2a18731f69d855fbce8ce822a21da9364fa
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Add required code to support FCONF on STM32MP1 platform.
The new FW_CONFIG DT file will be inside the FIP, and loaded by BL2.
It will be used to configure the addresses where to load other binaries.
BL2 should be agnostic of which BL32 is in the FIP (OP-TEE or SP_min),
so optee_utils.c is always compiled, and some OP-TEE flags are removed.
Change-Id: Id957b49b0117864136250bfc416664f815043ada
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Instead of using a scratch buffer of 512 bytes, we can directly use the
image address and max size. The mmc_block_dev_spec struct info is then
overwritten for each image with this info, except FW_CONFIG and GPT
table which will still use the scratch buffer.
This allows using multiple blocks read on MMC, and so improves the boot
time.
A cache invalidate is required for the remaining data not used from the
first and last blocks read. It is not required for FW_CONFIG_ID,
as it is in scratch buffer in SYSRAM, and also because bl_mem_params
struct is overwritten in this case. This should also not be done if
the image is not found (OP-TEE extra binaries when using SP_min).
Change-Id: If3ecfdfe35bb9db66284036ca49c4bd1be4fd121
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
BL2 still uses the STM32 header binary format to be loaded from ROM code.
BL32 and BL33 and their respective device tree files are now put together
in a FIP file.
One DTB is created for each BL. To reduce their sizes, 2 new dtsi file are
in charge of removing useless nodes for a given BL. This is done because
BL2 and BL32 share the same device tree files base.
The previous way of booting is still available, the compilation flag
STM32MP_USE_STM32IMAGE has to be set to 1 in the make command. Some files
are duplicated and their names modified with _stm32_ to avoid too much
switches in the code.
Change-Id: I1ffada0af58486d4cf6044511b51e56b52269817
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Protect BL32 (SP_min) with MMU if OP-TEE is not used.
Validate OP-TEE header with optee_header_is_valid().
Use default values in bl2_mem_params_descs[]. They will be overwritten
in bl2_plat_handle_post_image_load() if OP-TEE is used.
Change-Id: I8614f3a17caa827561614d0f25f30ee90c4ec3fe
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Embarrassingly we never told the non-secure world that secure firmware
lives in the first few hundred KBs of DRAM, so any non-secure payload
could happily overwrite TF-A, and we couldn't even blame it.
Advertise the BL31 region in the reserved-memory DT node, so non-secure
world stays out of it.
This fixes Linux booting on FPGAs with less memory than usual.
Change-Id: I7fbe7d42c0b251c0ccc43d7c50ca902013d152ec
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* changes:
refactor(plat/nxp): refine api to read SVR register
refactor(plat/nxp): each errata use a seperate source file
refactor(plat/nxp): use a unified errata api
refactor(plat/soc-lx2160): move errata to common directory
At the moment we specified the BL31 memory limits to 1MB; since we
typically have gigabytes of DRAM, we can be quite generous.
However the default parameters expect the devicetree binary at
0x80070000, so we should actually make sure we have no code or data
beyond that point.
Limit the ARM FPGA BL31 memory footprint to this available 7*64K region.
We stay within the limit at the moment, with more than half of it
reserved for stacks, so this could be downsized later should we run
into problems.
The PIE addresses stay as they are, since the default addresses do not
apply there anywhere, and the build is broken anyway.
Change-Id: I7768af1a93ff67096f4359fc5f5feb66464bafaa
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently the list of SP UUIDs loaded by BL2 is hardcoded in the DT.
This is a problem when building a system with other SPs (e.g. from
Trusted Services). This commit implements a workaround to enable adding
SP UUIDs to the list at build time.
Signed-off-by: Balint Dobszay <balint.dobszay@arm.com>
Change-Id: Iff85d3778596d23d777dec458f131bd7a8647031
Up until now we relied on the GICs used in our FPGA images to be GICv3
compliant, without the "direct virtual injection" feature (aka GICv4)
enabled.
To support newer images which have GICv4 compliant GICs, enable the
newly introduced GICv4 detection code, and use that also when we adjust
the redistributor region size in the devicetree.
This allows the same BL31 image to be used with GICv3 or GICv4 FPGA
images.
Change-Id: I9f6435a6d5150983625efe3650a8b7d1ef11b1d1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we have a GIC_ENABLE_V4_EXTN build time variable to
determine whether the GIC interrupt controller is compliant to version
4.0 of the spec or not. This just changes the number of 64K MMIO pages
we expect per redistributor.
To support firmware builds which run on variable systems (emulators,
fast model or FPGAs), let's make this decision at runtime.
The GIC specification provides several architected flags to learn the
size of the MMIO frame per redistributor, we use GICR_TYPER[VLPI] here.
Provide a (static inline) function to return the size of each
redistributor.
We keep the GIC_ENABLE_V4_EXTN build time variable around, but change
its meaning to enable this autodetection code. Systems not defining this
rely on a "pure" GICv3 (as before), but platforms setting it to "1" can
now deal with both configurations.
Change-Id: I9ede4acf058846157a0a9e2ef6103bf07c7655d9
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
1. Refined struct soc_info_t definition.
2. Refined get_soc_info function.
3. Fixed some SVR persernality value.
4. Refined API to get cluster numbers and cores per cluster.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I3c20611a523516cc63330dce4c925e6cda1e93c4
This patch adds the necessary files to support
the SolidRun CN913X CEx7 Evaluation Board.
Because the DRAM connectivity and SerDes settings
is shared with the CN913X DB - reuse relevant
board-specific files.
Change-Id: I75a4554a4373953ca3fdf3b04c4a29c2c4f8ea80
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
The common makefile used by every a8k/cn913x platform
(a8k_common.mk) assumed default paths in PLAT_INCLUDES,
BLE/BL31_PORTING_SOURCES. Allow overriding those
variables, in order to avoid code duplication.
It can be helpful in case using multiple board variants
or sharing common settings between different platforms.
Change-Id: Idce603e44ed04d99fb1e3e11a2bb395d552e2bf7
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
* changes:
feat(plat/allwinner): add R329 support
refactor(plat/allwinner): allow custom BL31 offset
refactor(plat/allwinner): allow new AA64nAA32 position
fix(plat/allwinner): delay after enabling CPU power
Use a unfied API soc_errata() for each platforms,
add print a INFO message for each enabled errata,
so that it will be easy to check which errata is
enabled on current platform.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I5eab3f338db6b46c57cbad475819043fc60ca6d3
Will add more Erratas, some errata can be used for multiple
platforms, so move errata to be common code which can
be share between different platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Ib149b3eac365bdb593331e9f38f0b89d92c9c0d1
Allwinner R329 is a new dual-core Corte-A53 SoC. Add basical TF-A
support for it, to provide a PSCI implementation containing CPU
boot/shutdown and SoC reset.
Change-Id: I0fa37ee9b4a8e0e1137bf7cf7d614b6ca9624bfe
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Not all Allwinner SoCs have the same arrangement to SRAM A2.
Allow to specify a offset at which BL31 will stay in SRAM A2.
Change-Id: I574140ffd704a796fae0a5c2d0976e85c7fcbdf9
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
In newer Allwiner SoCs, the AA64nAA32 wires are mapped to a new register
called "General Control Register0" in the manual rather than the
"Cluster 0 Control Register0" in older SoCs.
Now the position of AA64nAA32 (reg and bit offset) is defined in a few
macros instead assumed to be at bit offset 24 of
SUNXI_CPUCFG_CLS_CTRL_REG0.
Change-Id: I933d00b9a914bf7103e3a9dadbc6d7be1a409668
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Adds a 1us delay after enabling power to a CPU core, to prevent
inrush-caused CPU crash before it's up.
Change-Id: I8f4c1b0dc0d1d976b31ddc30efe7a77a1619b1b3
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Add TZC master source id for DMA in the SoC space and for the DMAs
behind the I/O Virtualization block to allow the non-secure transactions
from these DMAs targeting DRAM.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Change-Id: I77a2947b01b4b49a7c1940f09cf62b7b5257657c
It was enabled in commit 3c7dcdac5c ("marvell/a3700: Prevent SError
accessing PCIe link while it is down") with a workaround for a bug found
in U-Boot and Linux kernel driver pci-aardvark.c (PCIe controller driver
for Armada 37xx SoC) which results in SError interrupt caused by AXI
SLVERR on external access (syndrome 0xbf000002) and immediate kernel
panic.
Now when proper patches are in both U-Boot and Linux kernel projects,
this workaround in TF-A should not have to be enabled by default
anymore as it has unwanted side effects like propagating all external
aborts, including non-fatal/correctable into EL3 and making them as
fatal which cause immediate abort.
Add documentation for HANDLE_EA_EL3_FIRST build option into Marvell
Armada build section.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ic92b65bf9923505ab682830afb66c2f6cec70491
A3700 plat_ea_handler was introduced into TF-A codebase just because of
bugs in U-Boot and Linux kernel PCIe controller driver pci-aardvark.c.
These bugs were finally fixed in both U-Boot and Linux kernel drivers:
eccbd4ad8ehttps://git.kernel.org/stable/c/f18139966d072dab8e4398c95ce955a9742e04f7
Add all these information into comments, including printing error
message into a3k plat_ea_handler. Also check that abort is really
asynchronous and comes from lower level than EL3.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I46318d221b39773d5e25b3a0221d7738736ffdf1
The GIC IP formerly known as "GIC Clayton" has been released under the
name of "GIC-700".
Rename occurences of Clayton in comments and macro names to reflect the
official name.
Change-Id: Ie8c55f7da7753127d58c8382b0033c1b486f7909
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for runtime feature configuration which are running on the
firmware. Add new IOCTL IDs like IOCTL_SET_FEATURE_CONFIG and
IOCTL_GET_FEATURE_CONFIG for configuring the features.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I976aef15932783a25396b2adeb4c8f140cc87e79
Sync IOCTL IDs in order to avoid conflict with other components like,
Linux and firmware. Hence assigning value to IDs to make it more
specific.
Signed-off-by: Ronak Jain <ronak.jain@xilinx.com>
Change-Id: I11ae679fbd0a953290306b62d661cc142f50dc28
after this commit: If15cf3b9d3e2e7876c40ce888f22e887893fe696
plat/qemu/common/qemu_pm.c:116: (entrypoint < (NS_DRAM0_BASE + NS_DRAM0_SIZE)))
the above line (NS_DRAM0_BASE + NS_DRAM0_SIZE) = 0x100000000, which will
overflow 32bit and cause ERROR
SO add ULL to fix it
tested on compiler:
gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))
Signed-off-by: Darren Liang <lwp513@qq.com>
Change-Id: I1d769b0803142d37bd2968d765ab04a9c7c5c21a
This patch adds the basic CPU library code to support the Demeter
CPU. This CPU is based on the Makalu-ELP core so that CPU lib code
was adapted to create this patch.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ib5740b748008a72788c557f0654d8d5e9ec0bb7f
As done recently for plat/tc0 in b5863cab9, enable AMU explicitly.
This is necessary as the recent changes that enable SVE for the secure
world disable AMU by default in the CPTR_EL3 reset value.
Change-Id: Ie3abf1dee8a4e1c8c39f934da8e32d67891f5f09
Signed-off-by: Tom Cosgrove <tom.cosgrove@arm.com>
Now that the DDR is mapped secured, the security settings (TZC400
firewall) have to be applied at the end of BL2 for the OP-TEE case.
This is required to avoid checskum computation error on U-Boot binary,
for which MMU and TZC400 would not be aligned.
Change-Id: I4a364f7117960e8fae1b579f341b9f140b766ea6
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
The Tegra132 platforms have reached their end of life and are
no longer used in the field. Internally and externally, all
known programs have removed support for this legacy platform.
This change removes this platform from the Tegra tree as a result.
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Change-Id: I72edb689293e23b63290cdcaef60468b90687a5a
Most DTBs used on the RaspberryPi contain a FDT /memreserve/ region,
that covers the original secondaries' spin table.
We need to reserve more memory than described there, to cover the whole
of the TF-A image, so we add a /reserved-memory node to the DTB.
However having the same memory region described by both methods upsets
the Linux kernel and U-Boot, so we have to make sure there is only one
instance describing this reserved memory.
Keep our currently used /reserved-memory node, since it's more capable
(it allows to mark the region as secure memory). Add some code to drop
the original /memreserve/ region, since we don't need this anymore,
because we take the secondaries out of their original spin loop.
We explicitly check for the currently used size of 4KB for this region,
to be alerted by any changes to this region in the upstream DTB.
Change-Id: Ia3105560deb3f939e026f6ed715a9bbe68b56230
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Put default ea handler implementation into function plat_default_ea_handler()
which just print verbose information and panic, so it can be called also
from overwritten / weak function plat_ea_handler() implementation.
Replace every custom implementation of printing verbose error message of
external aborts in custom plat_ea_handler() functions by a common
implementation from plat_default_ea_handler() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I15897f61b62b4c3c29351e693f51d4df381f3b98
* changes:
feat(plat/rcar3): emit RPC status to DT fragment if RPC unlocked
feat(plat/rcar3): add a DRAM size setting for M3N
feat(plat/rcar3): update IPL and Secure Monitor Rev.3.0.0
feat(plat/rcar3): add new board revision for Salvator-XS/H3ULCB
feat(drivers/rcar3): ddr: add function to judge a DDR rank
fix(drivers/rcar3): ddr: update DDR setting for H3, M3, M3N
fix(drivers/rcar3): i2c_dvfs: fix I2C operation
fix(drivers/rcar3): fix CPG registers redefinition
fix(drivers/rcar3): emmc: remove CPG_CPGWPR redefinition
fix(plat/rcar3): generate two memory nodes for larger than 2 GiB channel 0
refactor(plat/rcar3): factor out DT memory node generation
feat(plat/rcar3): add optional support for gzip-compressed BL33
* changes:
feat(io_mtd): offset management for FIP usage
feat(nand): count bad blocks before a given offset
feat(plat/st): add helper to save boot interface
fix(plat/st): improve DDR get size function
refactor(plat/st): map DDR secure at boot
refactor(plat/st): rework TZC400 configuration
This commit activates the stack protector feature for the diphda
platform.
Change-Id: Ib16b74871c62b67e593a76ecc12cd3634d212614
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
This renames tc0 platform folder and files to tc, and introduces
TARGET_PLATFORM variable to account for the differences between
TC0 and TC1.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I5b4a83f3453afd12542267091b3edab4c139c5cd
This reverts commit 4d9b9b2352.
Timeout in IPI ack was added for functional safety reason.
Functional safety is not criteria for ATF. However, this
creates issues for APIs that take long or non-deterministic
duration like FPGA load. So revert this patch for now to fix
FPGA loading issue. Need to add support for non-blocking API
for FPGA loading with callback when API completes.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I940e798f1e2f7d0dfca1da5caaf8b94036d440c6
DFD (Design for Debug) is a debugging tool, which scans
flip-flops and dumps to internal RAM on the WDT reset.
After system reboots, those values could be showed for
debugging.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: I9c7af9a4f75216ed2c6b44458d121a352bef4b95
Fixed the build error by removing the local definition of 'efi_guid'
structure in 'sgi_ras.c' file as this structure definition is already
populated in 'sgi_ras.c' file via 'uuid.h' header.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I57687336863f2a0761c09b6c1aa00b4aa82a6a12
Bump the required FF-A version in framework and manifests to v1.1 as
upstream feature development goes.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I89b2bd3828a13fc4344ccd53bc3ac9c0c22ab29f
Renamed hw_crc32 to tf_crc32 to make the file and function
name more generic so that the same name can be used in upcoming
software CRC32 implementation.
Change-Id: Idff8f70c50ca700a4328a27b49d5e1f14d2095eb
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Added firmware update support in Arm platforms by using
FWU platform hooks and compiling FWU driver in BL2
component.
Change-Id: I71af06c09d95c2c58e3fd766c4a61c5652637151
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
External Abort may happen also during printing of some messages by
U-Boot or kernel. So print newline before fatal abort error message.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ic7579b605e695c2e4cb9a4f5cdc2d0b3e5083e49
These files are needed during boot, but they were missing
for semihosting.
With this patch, the list of files is complete enough to
boot on ATF platform via semihosting.
Change-Id: I2f0ca25983a6e18096f040780776f19f8040ea79
Signed-off-by: stsp@users.sourceforge.net
The rpi4 has a single nonstandard ECAM. It is broken
into two pieces, the root port registers, and a window
to a single device's config space which can be moved
between devices. Now that we have widened the page
tables/MMIO window, we can create a read/write acces
functions that are called by the SMCCC/PCI API.
As an example platform, the rpi4 single device ECAM
region quirk is pretty straightforward. The assumption
here is that a lower level (uefi) has configured and
initialized the PCI root to match the values we are
using here.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Change-Id: Ie1ffa8fe9aa1d3c62e6aa84746a949c1009162e0
Now that we have adjusted the address map, added the
SMC conduit code, and the RPi4 PCI callbacks, lets
add the flags to enable everything in the build.
By default this service is disabled because the
expectation is that its only useful in a UEFI+ACPI
environment.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Change-Id: I2a3cac6d63ba8119d3b711db121185816b89f8a2
* changes:
refactor(plat/allwinner): clean up platform definitions
refactor(plat/allwinner): do not map BL32 DRAM at EL3
refactor(plat/allwinner): map SRAM as device memory by default
refactor(plat/allwinner): rename static mmap region constant
feat(bl_common): import BL_NOBITS_{BASE,END} when defined
Recent changes to enable SVE for the secure world have disabled AMU
extension by default in the reset value of CPTR_EL3 register. So the
platform has to enable this extension explicitly.
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: I7d930d96ec22d7c3db961411370564bece0ce272
Group the SCP base/size definitions in a more logical location.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Id43f9b468d7d855a2413173d674a5ee666527808
BL31 does not appear to ever access the DRAM allocated to BL32,
so there is no need to map it at EL3.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ie8727b793e53ea14517894942266f6da0333eb74
The SRAM on Allwinner platforms is shared between BL31 and coprocessor
firmware. Previously, SRAM was mapped as normal memory by default.
This scheme requires carveouts and cache maintenance code for proper
synchronization with the coprocessor.
A better scheme is to only map pages owned by BL31 as normal memory,
and leave everything else as device memory. This removes the need for
cache maintenance, and it makes the mapping for BL31 RW data explicit
instead of magic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I820ddeba2dfa2396361c2322308c0db51b55c348
This constant specifically refers to the number of static mmap regions.
Rename it to make that clear.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: I475c037777ce2a10db2631ec0e7446bb73590a36
At this stage of development Non Volatile counters are not implemented
in the Diphda platform.
This commit disables their use during the Trusted Board Boot by
overriding the NV counters get/set functions.
Change-Id: I8dcbebe0281cc4d0837c283ff637e20b850988ef
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
This commit enables trusted-firmware-a with Trusted Board Boot support
for the Diphda 64-bit platform.
Diphda uses a FIP image located in the flash. The FIP contains the
following components:
- BL2
- BL31
- BL32
- BL32 SPMC manifest
- BL33
- The TBB certificates
The board boot relies on CoT (chain of trust). The trusted-firmware-a
BL2 is extracted from the FIP and verified by the Secure Enclave
processor. BL2 verification relies on the signature area at the
beginning of the BL2 image. This area is needed by the SecureEnclave
bootloader.
Then, the application processor is released from reset and starts by
executing BL2.
BL2 performs the actions described in the trusted-firmware-a TBB design
document.
Signed-off-by: Rui Miguel Silva <rui.silva@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Change-Id: Iddb1cb9c2a0324a9635e23821c210ac81dfc305d
Align documentation with changes of messaging method for partition
manifest:
- Bit[0]: support for receiving direct message requests
- Bit[1]: support for sending direct messages
- Bit[2]: support for indirect messaging
- Bit[3]: support for managed exit
Change the optee_sp_manifest to align with the new messaging method
description.
Signed-off-by: Maksims Svecovs <maksims.svecovs@arm.com>
Change-Id: I333e82c546c03698c95f0c77293018f8dca5ba9c
This patch adds the option HARDEN_SLS_ALL that can be used to enable
the -mharden-sls=all, which mitigates the straight-line speculation
vulnerability. Enable this by adding the option HARDEN_SLS_ALL=1,
default this will be disabled.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I0d498d9e96903fcb879993ad491949f6f17769b2
When enabling U-boot with UEFI and secure boot, the size of U-boot
becomes more than 1MB. So we enlarge BL33 to 2MB.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I9d9d24132bb1ec17ef6080dc72e93c7f531c97b5
* changes:
refactor(plat/arm): use mmio* functions to read/write NVFLAGS registers
refactor(plat/arm): mark the flash region as read-only
refactor(plat/arm): update NV flags on image load/authentication failure
* changes:
fix(plat/marvell/a3k): Fix building uart-images.tgz.bin archive
refactor(plat/marvell/a3k): Rename *_CFG and *_SIG variables
refactor(plat/marvell/a3k): Rename DOIMAGETOOL to TBB
refactor(plat/marvell/a3k): Remove useless DOIMAGEPATH variable
fix(plat/marvell/a3k): Fix check for external dependences
fix(plat/marvell/a8k): Add missing build dependency for BLE target
fix(plat/marvell/a8k): Correctly set include directories for individual targets
fix(plat/marvell/a8k): Require that MV_DDR_PATH is correctly set
There is a error setting for SPM, so we need to fix this issue.
Signed-off-by: Garmin Chang <garmin.chang@mediatek.com>
Change-Id: I741a5dc1505a831fe48fd5bc3da9904db14c8a57
This change adds 208 bytes to PMUSRAM, pushing the end of text from
0xff3b0de0 to 0xff3b0eb0, which is still shy of the maximum
0xff3b1000.
Further, this skips enabling the watchdog when it's not being used
elsewhere, as you can't turn the watchdog off.
Change-Id: I2e6fa3c7e01f2be6b32ce04ce479edf64e278554
Signed-off-by: Jimmy Brisson <jimmy.brisson@arm.com>
Some parameters from BootROM boot context can be required after boot.
To save space in SYSRAM, this context can be overwritten during images
load sequence. The needed information (here the boot interface) is
then saved in a local variable.
Change-Id: I5e1ad4630ccf78480f415a0a83939005ae67729e
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Avoid parsing device tree every time when returning
the DDR size.
A cache flush on this size is also added because TZC400 configuration
is applied at the end of BL2 after MMU and data cache being turned off.
Configuration needs to retrieve the DDR size to generate the correct
region. Access to the size fails because the value is still in the data
cache. Flushing the size is mandatory.
Change-Id: I3dd1958f37d806f9c15a5d4151968935f6fe642e
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
In BL2, the DDR can be mapped as secured in MMU, as no other SW
has access to it during its execution.
The TZC400 configuration is also updated to reflect this. When using
OP-TEE, the TZC400 is reconfigured at the end of BL2, to match OP-TEE
mapping. Else, SP_min will be in charge to reconfigure TZC400 to set
DDR non-secure.
Change-Id: Ic5ec614b218f733796feeab1cdc425d28cc7c103
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Add new static functions to factorize code in stm32mp1_security.c.
Change-Id: Ifa5a1aaf7c56c25dba9a0ab8e985496d7cb06990
Signed-off-by: Yann Gautier <yann.gautier@st.com>
For UART secure boot it is required also TIMN image, so pack it into
uart-images.tgz.bin archive which is created by mrvl_uart target.
$(TIMN_IMAGE) and $(TIM_IMAGE) variables are used only for UART images
so their content needs to be initialized from $(TIMN_UART_CFG) and
$(TIM_UART_CFG) config files. And not from $(TIMN_CFG) and $(TIM_CFG) as
it is now because they are not generated during mrvl_uart target. Fix it
to allow building mrvl_uart target before mrvl_flash target.
To match usage of these variables, rename them to $(TIMN_UART_IMAGE) and
$(TIM_UART_IMAGE).
To not complicate rule for building uart-images.tgz.bin archive, set
list of image files into a new $(UART_IMAGES) variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I83b980abb4047a3afb3ce3026842e1d873c490bf
For TIM config file use TIM name instead of DOIMAGE and use underscores
to make variable names more readable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I1282ce11f1431c15458a143ae7bfcee85eed2432
In case the RCAR_RPC_HYPERFLASH_LOCKED is 0, emit DT node /soc/rpc@ee200000
with property status = "okay" into the DT fragment passed to subsequent
software, to indicate the RPC is unlocked.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Id93c4573ab1c62cf13fa5a803dc5818584a2c13a
Armada 3700 uses external TBB tool for creating images and does not use
internal TF-A doimage tool from tools/marvell/doimage/
Therefore set correct name of variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I38a94dca78d483de4c79da597c032e1e5d06d92d
Old Marvell a3700_utils and mv-ddr tarballs do not have to work with
latest TF-A code base. Marvell do not provide these old tarballs on
Extranet anymore. Public version on github repository contains all
patches and is working fine, so for public TF-A builds use only public
external dependencies from git.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iee5ac6daa9a1826a5b80a8d54968bdbb8fe72f61
BLE source files depend on external Marvell mv-ddr-marvell tree
(specified in $(MV_DDR_PATH) variable) and its header files. Add
dependency on $(MV_DDR_LIB) target which checks that variable
$(MV_DDR_PATH) is correctly set and ensures that make completes
compilation of mv-ddr-marvell tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I73968b24c45d9af1e3500b8db7a24bb4eb2bfa47
Do not set all include directories, including those for external targets
in one PLAT_INCLUDES variable.
Instead split them into variables:
* $(PLAT_INCLUDES) for all TF-A BL images
* BLE target specific $(PLAT_INCLUDES) only for Marvell BLE image
* $(MV_DDR_INCLUDES) for targets in external Marvell mv-ddr-marvell tree
Include directory $(CURDIR)/drivers/marvell is required by TF-A BL
images, so move it from ble.mk to a8k_common.mk.
Include directory $(MV_DDR_PATH) is needed only by Marvell BLE image, so
move it into BLE target specific $(PLAT_INCLUDES) variable.
And remaining include directories specified in ble.mk are needed only
for building external dependences from Marvell mv-ddr tree, so move them
into $(MV_DDR_INCLUDES) variable and correctly use it in $(MV_DDR_LIB)
target.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I331f7de675dca2bc70733d56b768f00d56ae4a67
Target mrvl_flash depends on external mv_ddr source code which is not
part of TF-A project. Do not expect that it is pre-downloaded at some
specific location and require user to specify correct path to mv_ddr
source code via MV_DDR_PATH build option.
TF-A code for Armada 37x0 platform also depends on mv_ddr source code
and already requires passing correct MV_DDR_PATH build option.
So for A8K implement same checks for validity of MV_DDR_PATH option as
are already used by TF-A code for Armada 37x0 platform.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I792f2bfeab0cec89b1b64e88d7b2c456e22de43a
This commit adds a DRAM size setting when building with
RCAR_DRAM_LPDDR4_MEMCONF=2 for M3N Ver.1.1 4GB DRAM.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: Ib7fea862ab2e0bcafaf39ec030384f0fddda9b96
Update the revision number in the revision management file.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I44b9e5a992e8a44cfeafad6d2c1a97aa59baca4e
This commit deletes the value of the redefined CPG register.
Signed-off-by: Toshiyuki Ogasahara <toshiyuki.ogasahara.bo@hitachi.com>
Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Change-Id: I05cf4a449ae28adb2ddd59593971a7d0cbcb21de
The DRAM channel 0 memory area in 32bit space is limited to 2 GiB window.
Furthermore, the first 128 MiB of this memory window are reserved and not
accessible by the system software, hence the 32bit area memory node is
limited to range 0x4800_0000..0xbfff_ffff.
In case there are more than 2 GiB of DRAM populated in channel 0, it is
necessary to generate two memory nodes, once covering the 2 GiB - 128 MiB
area in the 32bit space, and another covering the rest of the memory in
64bit space. This patch implements handling of such a case.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: I3495241fb938e355352e817afaca8f01d04c81d2
Move the code that adds single new memory@ node into the DT fragment passed
to system software into separate function. Adjust the failure message to be
more specific and print the address range of node which failed to be added.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Ie42cd7756b045271f070bca93c524fff6238f5a2
The BL33 size on this platform is limited to 1 MiB, add optional
support for decompressing and starting gzip-compressed BL33, which
may help with this size limitation. This functionality is disabled
by default, set RCAR_GEN3_BL33_GZIP=1 during build to enable it.
The BL33 at 0x50000000 should then be gzip compressed, however if
the BL33 does not have a valid gzip header, it is copied to the
correct location and started as-is, this is a fallback for legacy
systems and systems which update to gzip-compressed BL33.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Change-Id: Id93f1c7e6f17db1ffb952ea086562993473f6efa
All API calls except non-blocking should wait for
IPI response and read buffer to check return status
from firmware. Some of API calls are not reading
status from IPI payload data. Use sync method which
reads actual return status from IPI payload.
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: I6f568b85d0da639c264f507122e3015807d8423d
All API calls except non-blocking should wait for
IPI response and read buffer to check return status
from firmware. Some of API calls are not reading
status from IPI payload data. Use sync method which
reads actual return status from IPI payload.
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: I78f9c061a80cee6d524ade4ef124ca88ce1848cf
Used mmio* functions to read/write NVFLAGS registers to avoid
possibile reordering of instructions by compiler.
Change-Id: Iae50ac30e5413259cf8554f0fff47512ad83b0fd
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
In the FVP platform, BL1 uses flash only for read purpose
hence marked this flash region as read-only.
Change-Id: I3b57130fd4f3b4df522ac075f66e9799f237ebb7
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Erasing the FIP TOC header present in a flash is replaced by updating NV
flags with an error code on image load/authentication failure.
BL1 component uses these NV flags to detect whether a firmware update is
needed or not.
These NV flags get cleared once the firmware update gets completed.
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Change-Id: I6232a0db07c89b2373b7b9d28acd37df6203d914
DCM means dynamic clock management, and it can dynamically
slow down or gate clocks during CPU or bus idle.
1. Add MCUSYS related DCM drivers.
2. Enable MCUSYS related DCM by default.
Change-Id: I3237199bc217bd3682f51d31284db5fd0324b396
Signed-off-by: Garmin Chang <garmin.chang@mediatek.com>
In the qemu memory map 1GB and up is RAM. Change the
size of NS DRAM to 3GB to support VM's with more
memory requirements.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Change-Id: If15cf3b9d3e2e7876c40ce888f22e887893fe696
* changes:
feat(plat/mediatek/mt8195): add SPM suspend driver
feat(plat/mediatek/mt8195): support MCUSYS off when system suspend
feat(plat/mediatek/mt8195): add support for PTP3
fix(plat/mediatek/mt8195): extend MMU region size
Support DRAM/MAINPLL/26M off when system suspend.
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Change-Id: Ib8502f9b0b4e47aa405e5449f0b6d483bd3f5d77
Add drivers to support MCUSYS off when system suspend.
Signed-off-by: Edward-JW Yang <edward-jw.yang@mediatek.corp-partner.google.com>
Change-Id: I388fd2318f471083158992464ecdf2181fc7d87a
Add PTP3 drivers to protect CPU excessive voltage drop
in CPU heavy loading.
Change-Id: I7bd37912c32d5328ba0287fccc8409794bd19c1d
Signed-off-by: Elly Chiang <elly.chiang@mediatek.com>
In mt8195 suspend/resume flow, ATF has to communicate with a subsys by
read/write the subsys registers. However, the register region of subsys
doesn't include in the MMU mapping region. It triggers MMU faults.
This patch extends the MMU region 0 size to cover all mt8195 HW modules.
This patch also remove MMU region 1 because region 0 covers region 1.
Change-Id: I3a186ed71d0d963b59ae55e27a6d27a01fe4f638
Signed-off-by: Tinghan Shen <tinghan.shen@mediatek.com>
The partition layout description JSON file generated by TF-A tests
declares a fourth test partition called Ivy demonstrating the
implementation of a S-EL0 partition supported by a S-EL1 shim.
Change-Id: If8562acfc045d6496dfdb3df0524b3a069357f8e
Signed-off-by: Daniel Boulby <daniel.boulby@arm.com>
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Add a generic function to setup the stm32image IO.
Change-Id: I0f7cf4a6030605037643f3119b809e0319d926af
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Add a panic() at the end of stm32mp_io_setup() if the boot interface
given in ROM code boot context is not supported.
Change-Id: I0d50f21a11231febd21041b6e63108cc3e6f4f0c
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
We don't ever expect to load a binary with an STM32 header on the Arm
FVP platform so remove this type of image from the list of
measurements.
Also remove the GPT image type from the list, as it does not get
measured. GPT is a container, just like FIP is. We don't measure the FIP
but rather the images inside it. It would seem logical to treat GPT the
same way.
Besides, only images that get loaded through load_auth_image() get
measured right now. GPT processing happens before that and is handled in
a different way (see partition_init()).
Change-Id: Iac4de75380ed625b228e69ee4564cf9e67e19336
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
For Arm platforms PIE is enabled when RESET_TO_BL31=1 in aarch64 mode on
the similar lines enable PIE when RESET_TO_SP_MIN=1 in aarch32 mode.
The underlying changes for enabling PIE in aarch32 is submitted in
commit 4324a14bf
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ib8bb860198b3f97cdc91005503a3184d63e15469
Third instance of cactus is a UP SP. Set its vcpu count to 1.
Signed-off-by: Arunachalam Ganapathy <arunachalam.ganapathy@arm.com>
Change-Id: I34b7feb2915e6d335e690e89dea466e75944ed1b
This patch will make BL2_BASE to be hex valaue but
not a shell command.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Iebb86a0b9bc8cab1676bd8e898cf4a1b6d16f472
Some build variables have already defined in common
make helper file, use them directly.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I7fe6331160bfdf315924d4498d78b0a399eb2e89
To quote jwerner in T925:
"The __sramdata in the declaration is a mistake, the correct target
section for that global needs to be .pmusram.data. This used to be
in .sram.data once upon a time but then the suspend.c stuff got added
and required it to be moved to PMUSRAM. I guess they forgot to update
that part in the declaration and since the old GCC seemed to silently
prefer the attribute in the definition, nobody noticed."
This fixes building with gcc 11.
fix #T925
Change-Id: I2b91542277c95cf487eaa1344927294d5d1b8f2b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
In stm32mp1_syscfg_disable_io_compensation(), to disable the IO
compensation cell, we have to set the corresponding bit in
SYSCFG_CMPENCLRR register, instead of clearing the bit in SETR register.
Change-Id: I510a50451f8afb9e98c24e1ea84efbf73a39e6b4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The dependency on this macro was added by patch [1]. But the macro
itself was forgotten in the patch.
[1] 128e0b3e2e ("stm32mp1: update rules for stm32image tool")
Change-Id: I49219e1e13828b97b95f404983da33ef4567fe23
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
BSEC services should return SMC error codes as other IDs (defined in
stm32mp1_smc.h) and not BSEC driver ones. So that non-secure caller
is able to treat them correctly.
In global SMC handler, unknown ID should also return a value from this
definition list, and not the generic one, which seems not well adapted
for our needs.
Two unsigned values initializations are also changed from 0 to 0U.
Change-Id: Ib6fd3866a748cefad1d13d48f7be38241621023e
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
As there is constraint with the space for the release builds,
remove some of the legacy code.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I5b8b16f34ed8e480f16ab1aeac80b85cdb391852
Add imx_system_reset2 which extends existing SYSTEM_RESET. It provides
architectural reset definitions and vendor-specific resets.
By default warm reset is triggered.
Also refactor existing implementation of wdog reset, add details about
each flag used.
Change-Id: Ia7348c32c385f1c61f8085776e81dd1e38ddda5c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
* changes:
feat(plat/nxp/lx2): add SUPPORTED_BOOT_MODE definition
feat(plat/nxp/common): add build macro for BOOT_MODE validation checking
refactor(plat/nxp/common): moved soc make-variables to new soc_common_def.mk
refactor(plat/nxp/lx216x): clean up platform configure file
refactor(plat/nxp/common): moved plat make-variables to new plat_common_def.mk
* changes:
refactor(plat/nvidia): use SOC_ID defines
refactor(plat/mediatek): use SOC_ID defines
refactor(plat/arm): use SOC_ID defines
feat(plat/st): implement platform functions for SMCCC_ARCH_SOC_ID
refactor(plat/st): export functions to get SoC information
feat(smccc): add bit definition for SMCCC_ARCH_SOC_ID
Add macro of SUPPORTED_BOOT_MODE for board lx2160ardb, lx2160aqds,
lx2162aqds.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I4451ca030eca79c9bc5fee928eec497a7f0e878c
1. Added the build macro "add_boot_mode_define".
2. Use the macro to validate current BOOT_MODE against the
pre-determined list of SUPPORTED_BOOT_MODE, so each platform
need to define the list: SUPPORTED_BOOT_MODE.
3. Reports error if BOOT_MODE is not in SUPPORTED_BOOT_MODE list,
or BOOT_MODE is not supported yet althoug it is in SUPPORTED_BOOT_MODE.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I29be60ecdb19fbec1cd162e327cdfb30ba629b07
Move some soc make variables to new soc_common_def.mk,
then it can be reused by other platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: Ia30bd332c95b6475f1cfee2f03a8ed3892a9568d
Use common code in common file to configure platform.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I72fe22751f12b8a4996a7b9f75fae4c912ea86de
Move some common make variables to new plat_common_def.mk,
then it can be reused by other platforms.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Change-Id: I37bd65b0f8124f63074fa03339f886c2cdb30bd3
In case of TF-A running out of DDR there is a need to reserved
memory to let other SW know that none can't use this memory. HW
wise this region can be (and should be) also protected by
protection unit XMPU. This is the first step to add reserved
memory location to DT.
DT address corresponds with default address in U-Boot and also
default address in Xilinx BSPs.
Code is valid only when TF-A runs out of DDR. When it runs out
of OCM there is no need to reseve anything because OCM is hidden
to OS.
Change-Id: I01f230ced67207a159128cc11d11d36dd4590cab
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add sdei support for i.MX8MM, this is to let jailhouse Hypervisor
could use SDEI to do hypervisor management, after physical IRQ
has been disabled routing.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change-Id: I8308c629448bd8adca9d3d25701adcf0c5a6afc2
Add sdei support for i.MX8MN, this is to let jailhouse Hypervisor
could use SDEI to do hypervisor management, after physical IRQ
has been disabled routing.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change-Id: Ie15fffdd09e1bba1b22334b8ccac2335c96b8b4d
Device Tree address is now a parameter for dt_open_and_check() function.
This will allow better flexibility when introducing PIE and FIP.
The fdt pointer is now only assigned if the given address holds
a valid device tree file. This allows removing the fdt_checked variable,
as we now check fdt is not null.
Change-Id: I04cbb2fc05c9c711ae1c77d56368dbeb6dd4b01a
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The boot device is now checked inside a dedicated rule, that is only
called during BL2 compilation step
Change-Id: Ie7bcd1f166285224b0c042238989a82f7b6105c6
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Added a new STM32MP_EMMC_BOOT option, which is used to look for SSBL in
the same eMMC boot partition TF-A booted from at a fixed 256k offset. In
case STM32 image header is not found, the boot process rolls back to a
GPT partition look-up scheme.
Signed-off-by: Vyacheslav Yurkov <uvv.mail@gmail.com>
Change-Id: I85a87dc9ae7f2b915ed8e584be80f4b3588efc48
Add basic SDEI support, implementing the software event 0 only for now.
This already allows hypervisors like Jailhouse to use SDEI for internal
signaling while passing the GICC through to the guest (see also IMX8).
With SDEI on, we overrun the SRAM and need to stay in DRAM. So keep SDEI
off by default.
Co-developed-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Change-Id: Ic0d71b4ef0978c0a34393f4e3530ed1e24a39ca2
The io_dummy code and function calls are only used in case BL32 is TF-A
SP_min, and not OP-TEE. This code in bl2_io_storage can then be put under
#ifndef AARCH32_SP_OPTEE.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I52787a775160b335f97547203f653419621f5147
STM32MP1 does not use BL1, the loading of BL2 is done by ROM code. It is
then useless to have an entry BL2_IMAGE_ID in the policies.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I464cedf588114d60522433123f8dbef32ae36818
Fix a remainder from early prototyping. OP-TEE as a secure partition
does not need specific SMC function id pass through to EL3.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I2843d1b9a5eb4c966f82790e1655fb569c2de7d4
The UUID strings used in FW_CONFIG DT are not aligned with UUIDs defined
in include/tools_share/firmware_image_package.h for BL32_EXTRA1 and
TRUSTED_KEY_CERT.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I517f8f9311585931f2cb931e0588414da449b694
The UART code for the A3K platform assumes that UART parent clock rate
is always 25 MHz. This is incorrect, because the xtal clock can also run
at 40 MHz (this is board specific).
The frequency of the xtal clock is determined by a value on a strapping
pin during SOC reset. The code to determine this frequency is already in
A3K's comphy driver.
Move the get_ref_clk() function from the comphy driver to a separate
file and use it for UART parent clock rate determination.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I8bb18a2d020ef18fe65aa06ffa4ab205c71be92e
Macros PLAT_MARVELL_BOOT_UART* and PLAT_MARVELL_CRASH_UART* are defined
to same values. De-duplicate them into PLAT_MARVELL_UART* macros.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iae5daf7cad6a971e6f3dbe561df3d0174106ca7f
Macros PLAT_MARVELL_BL31_RUN_UART* are not used since commit
d7c4420cb8 ("plat/marvell: Migrate to multi-console API").
Remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I5ec959ef4de87dcfb332c017ad2599bf8af6ffc3
Morello exhibits the behavior similar to Juno wherein CNTBaseN.CNTFRQ
can be written but does not reflect the value of the CNTFRQ register
in CNTCTLBase frame. This doesn't follow ARM ARM in that the value
updated in CNTCTLBase.CNTFRQ is not reflected in CNTBaseN.CNTFRQ.
Hence enable the workaround (applied to Juno) for Morello that updates
the CNTFRQ register in the Non Secure CNTBaseN frame.
Change-Id: Iabe53bf3c25152052107e08321323e4bde5fbef4
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Add support for XCK26 silicon which is available on SOM board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: Ic98213328702903af8a79f487a2868f3e6d60338
This patch renames the Matterhorn, Matterhorn ELP, and Klein CPUs to
Cortex A710, Cortex X2, and Cortex A510 respectively.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: I056d3114210db71c2840a24562b51caf2546e195
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to 25 MHz.
The final UART divisor for default baudrate 115200 is not affected by
this change.
(Note that the parent clock rate should not be defined via a macro,
since the xtal clock can also be 40 MHz. This is outside of the scope of
this fix, though.)
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Iaa401173df87aec94f2dd1b38a90fb6ed0bf0ec6
Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].
[1] 13f3c5166f ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Iba0424a5787f9e510a60696d4033db1b49b243b2
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Ibe3c17acd2482b7779318c8a922a138dcace5554
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Ie1dbc54569086f6a74206b873fee664b4cdeea36
Use the macros that are now defined in include/lib/smccc.h.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I688a76277b729672835d51fafb68d1d6205b6ae4
The JEDEC information for STMicroelectronics is:
JEDEC_ST_MFID U(0x20)
JEDEC_ST_BKID U(0x0)
And rely on platform functions to get chip IP and revision.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I4fa4ac8bb5583b1871b768decc9fe08e8966ff54
Three functions are exported to get SoC version, SoC device ID, and SoC
name. Those functions are based on reworked existing static functions.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I1f3949062bb488286a9e7a38ffcd1457953dac56
The SGI/RD platforms have been using PSCI state ID format as defined in
PSCI version prior to 1.0. This is being changed and the PSCI extended
state ID format as defined in PSCI version 1.1 is being adapted. In
addition to this, the use of Arm recommended PSCI state ID encoding is
enabled as well.
Change-Id: I2be8a9820987a96b23f4281563b6fa22db48fa5f
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
Update idle flow in case of last read command timeout.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Change-Id: Idb0552d70d59b23822c38269d0fa9fe9ac0d6975
MTK display port mute/unmute control registers need to be
set in secure world.
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Iec73650e937bd20e25c18fa28d55ae29e68b10d3
Use proper offset for IPI data based on offset for IPI0
channel.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: I3070517944dd353c3733aa595df0da030127751a
The PCIe root port is outside of the current RPi
MMIO regions, so we need to adjust the address map.
Given much of the code depends on the legacy IOBASE
lets separate that from the actual MMIO begin/end.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Change-Id: Id65460ae58556bd8826dba08bbad79953e2a7c0b
Add APU iommap settings for reviser, apu_ao and
devapc control wrapper.
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Change-Id: Ie8e6a197c0f440f9e4ee8101202283a2dbf501a6
In iMX8MM it is possible to have two copies of bootloader in
SD/eMMC and switch between them. The switch is triggered either
by the BootROM in case the bootloader image is faulty OR can be
enforced by the user. To trigger that switch the
PERSIST_SECONDARY_BOOT bit should be set in GPR10 SRC register.
As the bit is retained after WARM reset, that permits to control
BootROM behavior regarding what boot image it will boot after
reset: primary or secondary.
This is useful for reliable bootloader A/B updates, as it permits
switching between two copies of bootloader at different offsets of
the same storage.
If the PERSIST_SECONDARY_BOOT is 0, the boot ROM uses address
0x8400 for the primary image. If the PERSIST_SECONDARY_BOOT is 1,
the boot ROM reads that secondary image table from address 0x8200
on the boot media and uses the address specified in the table for
the secondary image.
Secondary Image Table contains the sector of secondary bootloader
image, exluding the offset to that image (explained below in the
note). To generate the Secondary Image Table, use e.g.:
$ printf '\x0\x0\x0\x0\x0\x0\x0\x0\x33\x22\x11'
'\x00\x00\x10\x0\x0\x00\x0\x0\x0'
> /tmp/sit.bin
$ hexdump -vC /tmp/sit.bin
00000000 00 00 00 00
00000004 00 00 00 00
00000008 33 22 11 00 <--- This is the "tag"
0000000c 00 10 00 00 <--- This is the "firstSectorNumber"
00000010 00 00 00 00
You can also use NXP script from [1][2] imx-mkimage tool for
SIT generation. Note that the firstSectorNumber is NOT the offset
of the IVT, but an offset of the IVT decremented by Image Vector
Table offset (Table 6-25. Image Vector Table Offset and Initial
Load Region Size for iMX8MM/MQ), so for secondary SPL copy at
offset 0x1042 sectors, firstSectorNumber must be 0x1000
(0x42 sectors * 512 = 0x8400 bytes offset).
In order to test redundant boot board should be closed and
SD/MMC manufacture mode disabled, as secondary boot is not
supported in the SD/MMC manufacture mode, which can be disabled
by blowing DISABLE_SDMMC_MFG (example for iMX8MM):
> fuse prog -y 2 1 0x00800000
For additional details check i.MX 8M Mini Apllication Processor
Reference Manual, 6.1.5.4.5 Redundant boot support for
expansion device chapter.
[1] https://source.codeaurora.org/external/imx/imx-mkimage/
[2] scripts/gen_sit.sh
Change-Id: I0a5cea7295a4197f6c89183d74b4011cada52d4c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Added support for HW computed CRC using Arm ACLE intrinsics.
These are built-in intrinsics available for ARMv8.1-A, and
onwards.
These intrinsics are enabled via '-march=armv8-a+crc' compile
switch for ARMv8-A (supports CRC instructions optionally).
HW CRC support is enabled unconditionally in BL2 for all Arm
platforms.
HW CRC calculation is verified offline to ensure a similar
result as its respective ZLib utility function.
HW CRC calculation support will be used in the upcoming
firmware update patches.
Change-Id: Ia2ae801f62d2003e89a9c3e6d77469b5312614b3
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
Disable non-invasive debug of secure state for Juno
in release builds. This makes sure that PMU counts
only Non-secure events.
Signed-off-by: Zelalem Aweke <zelalem.aweke@arm.com>
Change-Id: I0d1c3f96f3b4e48360a7211ae55851d65d291025
This patch adds support for the crypto and secure storage secure
partitions for the Total Compute platform. These secure partitions
have to be managed by Hafnium executing at S-EL2
Change-Id: I2df690e3a99bf6bf50e2710994a905914a07026e
Signed-off-by: Davidson K <davidson.kumaresan@arm.com>
AMU counters are used for monitoring the CPU performance. RD-V1-MC
platform has architected AMU available for each core. Enable the use of
AMU by non-secure OS for supporting the use of counters for processor
performance control (ACPI CPPC).
Change-Id: I33be594cee669e7f4031e5e5a371eec7c7451030
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
on i.MX8MP A1 silicon, the OCRAM space is extended to 512K + 64K,
currently, OCRAM @0x960000-0x980000 is reserved for BL31, it will
leave the last 64KB in non-continuous space. To provide a continuous
384KB + 64KB space for generic use, so move the BL31 space to
0x970000-0x990000 range.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I96d572fc0f87f05a60f55e0552a68b6e70f8e7f4
the 'always_on' member should be initialized from 'on'.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Change-Id: I5746ff40075b4fcda2ac7d04a8d7f1269af17e91
* changes:
stm32mp1: enable PIE for BL32
stm32mp1: set BL sizes regardless of flags
Add PIE support for AARCH32
Avoid the use of linker *_SIZE__ macros
Added GPT parser support in BL2 for Arm platforms to get the entry
address and length of the FIP in the GPT image.
Also, increased BL2 maximum size for FVP platform to successfully
compile ROM-enabled build with this change.
Verified this change using a patch:
https://review.trustedfirmware.org/c/ci/tf-a-ci-scripts/+/9654
Change-Id: Ie8026db054966653b739a82d9ba106d283f534d0
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
NOTE: Breaking change to the way UUIDs are stored in the DT
Currently, UUIDs are stored in the device tree as
sequences of 4 integers. There is a mismatch in endianness
between the way UUIDs are represented in memory and the way
they are parsed from the device tree. As a result, we must either
store the UUIDs in little-endian format in the DT (which means
that they do not match up with their string representations)
or perform endianness conversion after parsing them.
Currently, TF-A chooses the second option, with unwieldy
endianness-conversion taking place after reading a UUID.
To fix this problem, and to make it convenient to copy and
paste UUIDs from other tools, change to store UUIDs in string
format, using a new wrapper function to parse them from the
device tree.
Change-Id: I38bd63c907be14e412f03ef0aab9dcabfba0eaa0
Signed-off-by: David Horstmann <david.horstmann@arm.com>
Replaced PLAT_ARM_FIP_BASE and PLAT_ARM_FIP_MAX_SIZE macro with a
generic name PLAT_ARM_FLASH_IMAGE_BASE and PLAT_ARM_FLASH_IMAGE_MAX_SIZE
so that these macros can be reused in the subsequent GPT based support
changes.
Change-Id: I88fdbd53e1966578af4f1e8e9d5fef42c27b1173
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
This new compile option is only for Armada 3720 Development Board. When
it is set to 1 then TF-A will setup PM wake up src configuration.
By default this new option is disabled as it is board specific and no
other A37xx board has PM wake up src configuration.
Currently neither upstream U-Boot nor upstream Linux kernel has wakeup
support for A37xx platforms, so having it disabled does not cause any
issue.
Prior this commit PM wake up src configuration specific for Armada 3720
Development Board was enabled for every A37xx board. After this change it
is enabled only when compiling with build flag A3720_DB_PM_WAKEUP_SRC=1
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I09fea1172c532df639acb3bb009cfde32d3c5766
Add board support for RD-N2 Cfg1 variant of RD-N2 platform. It is a
variant of RD-N2 platform with a reduced interconnect mesh size (3x3)
and core count (8-cores). Its platform variant id is 1.
Change-Id: I34ad35c5a5c1e9b69a658fb92ed00e5bc5fe72f3
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
A Neoverse reference design platform can have two or more variants that
differ in core count, cluster count or other peripherals. To allow reuse
of platform code across all the variants of a platform, introduce build
option CSS_SGI_PLATFORM_VARIANT for Arm Neoverse reference design
platforms. The range of allowed values for the build option is platform
specific. The recommended range is an interval of non negative integers.
An example usage of the build option is
make PLAT=rdn2 CSS_SGI_PLATFORM_VARIANT=1
Change-Id: Iaae79c0b4d0dc700521bf6e9b4979339eafe0359
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
This will help in keeping source file generic and conditional
compilation can be contained in platform provided dt files.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I3c6e0a429073f0afb412b9ba521ce43f880b57fe
sgm775 is an old platform and is no longer maintained by Arm and its
fast model FVP_CSS_SGM-775 is no longer available for download.
This platform is now superseded by Total Compute(tc) platforms.
This platform is now deprecated but the source will be kept for cooling
off period of 2 release cycle before removing it completely.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: I8fe1fc3da0c508dba62ed4fc60cbc1642e0f7f2a
mt8195 also uses mt6359p RTC. Revice mt8192 RTC and share the
driver with mt8195.
Change-Id: I20c73f6e0af67ef9d4c3d4e0ff373f93950e07db
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
mt8195 also uses PMIC mt6359p. The only difference is the
pwrap register definition.
Change-Id: I9962263c46187d1344f14f857bf4b51e33aedda0
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Implement PSCI platform OPs to support CPU hotplug and MCDI.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Change-Id: I1321f7989c8a3d116d698768a7146e8f180ee9c0
Add MCDI related drivers to handle CPU powered on/off in CPU suspend.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Change-Id: I6a6f9bf5d1d8bda1ee603d8bf3fc206437de7ad8
The timer driver can be shared with mt8195. Move the the timer
driver to common/.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I84c97ab9cc9b469f35e0f44dd8e7b2b95f1b3926
MT8192 cirq driver can be shared with MT8195. Move cirq driver to common
common folder.
Signed-off-by: gtk_pangao <gtk_pangao@mediatek.com>
Change-Id: Iba5cdcfd2116f0bd07e0497250f2da45613e3a4f
MT8192 GIC driver can be shared with MT8195. Move GIC driver to common
and do the initialization.
Signed-off-by: christine.zhu <christine.zhu@mediatek.corp-partner.google.com>
Change-Id: I63f3e668b5ca6df8bcf17b5cd4d53fa84f330fed
Upon recieving the interrupt send an SGI.
The sgi number is communicated by linux.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Change-Id: Ib8f07ff7132ba5ac202b546914efb16d04820ed3
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Add support for the trapping the IPI in TF-A.
Register handler for the irq no 62 which is the IPI interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Change-Id: I9c04fdae7be3dda6a34a9b196274c0b5fdf39223
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
* changes:
renesas: rzg: Add support to identify EK874 RZ/G2E board
drivers: renesas: common: watchdog: Add support for RZ/G2E
drivers: renesas: rzg: Add QoS support for RZ/G2E
drivers: renesas: rzg: Add PFC support for RZ/G2E
drivers: renesas: common: Add support for DRAM initialization on RZ/G2E SoC
renesas: rzg: Add support to identify HopeRun HiHope RZ/G2N board
drivers: renesas: common: emmc: Select eMMC channel for RZ/G2N SoC
drivers: renesas: rzg: Add QoS support for RZ/G2N
drivers: renesas: rzg: Add PFC support for RZ/G2N
drivers: renesas: common: Add support for DRAM initialization on RZ/G2N SoC
renesas: rzg: Add support to identify HopeRun HiHope RZ/G2H board
drivers: renesas: common: emmc: Select eMMC channel for RZ/G2H SoC
drivers: renesas: rzg: Add QoS support for RZ/G2H
drivers: renesas: rzg: Add PFC support for RZ/G2H
drivers: renesas: common: Add support for DRAM initialization on RZ/G2H SoC
drivers: renesas: rzg: Switch using common ddr code
drivers: renesas: ddr: Move to common
In order to prepare future support of FIP, BL32 (SP_min) is compiled
as Position Independent Executable.
Change-Id: I15e7cc433fb03e1833002f4fe2eaecb6ed42eb47
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
BL2 size is set to 100kB, and BL32 to 72kB, regardless of OP-TEE
or stack protector flags.
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id7411bd55a4140718d64a647d81037720615fc81
Counter frequency for generic timer of Arm-A53 based Application
Processing Unit(APU) is not configuring in case if First Stage Boot
Loader(FSBL) does not initialize counter frequency. This happens
when FSBL is running from Arm-R5 based Real-time Processing Unit(RPU).
Because of that generic timer driver functionality is not working.
So configure counter frequency during initialization.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Icfccd59d7d2340fba25ebfb2ef6a813af4290896
Add support for CRC checksum for IPI data when the macro
IPI_CRC_CHECK is enabled.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I3c25c715885759076055c6505471339b5d6edcd5
Rename the macro ZYNQMP_IPI_CRC_CHECK to IPI_CRC_CHECK and
move the related defines to the common include.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I6d30b081ac607572a0b23e10ca8031bc90489e58
ELP processors can sometimes have different MIDR values or features so
we are adding the "_arm" suffix to differentiate the reference
implementation from other future versions.
Signed-off-by: John Powell <john.powell@arm.com>
Change-Id: Ieea444288587c7c18a397d279ee4b22b7ad79e20
Add support to identify Silicon Linux RZ/G2E evaluation kit (EK874).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id7bdbc9b0d25aa9af496d58d4bd5055579edc104
DRAM initialization on RZ/G2E SoC is identical to R-Car E3 so re-use the
same.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I454fb40af4f8ce6c4c0d2a53edb307326efd02df
Add support for initializing DRAM on RZ/G2N SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Id09a367b92b11a5da88f2dce6887677cc935d0c0
Add support for initializing DRAM on RZ/G2H SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: Iae23f1093f65a9efd065d37b7d6e9340ff6350b9
Switch using common ddr driver code from renesas/common/ddr directory
for RZ/G2M SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I807dcb0bc5186bd32bc1c577945d28634bb10e1f
Move ddr driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Change-Id: I9aef73d3e9a027a127ce7483b72d339559866727
By default the Arm Ethos-N NPU will boot up in secure mode. In this mode
the non-secure world cannot access the registers needed to use the NPU.
To still allow the non-secure world to use the NPU, a SiP service has
been added that can delegate non-secure access to the registers needed
to use it.
Only the HW_CONFIG for the Arm Juno platform has been updated to include
the device tree for the NPU and the platform currently only loads the
HW_CONFIG in AArch64 builds.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: I65dfd864042ed43faae0a259dcf319cbadb5f3d2
To make it possible to use the hw_config device tree for dynamic
configuration in BL31 on the Arm Juno platform. A placeholder hw_config
has been added that is included in the FIP and a Juno specific BL31
setup has been added to populate fconf with the hw_config.
Juno's BL2 setup has been updated to align it with the new behavior
implemented in the Arm FVP platform, where fw_config is passed in arg1
to BL31 instead of soc_fw_config. The BL31 setup is expected to use the
fw_config passed in arg1 to find the hw_config.
Signed-off-by: Mikael Olsson <mikael.olsson@arm.com>
Change-Id: Ib3570faa6714f92ab8451e8f1e59779dcf19c0b6
Subversion is not reflecting the Marvell sources variant anymore.
This patch removes version.mk from Marvell plafroms.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I8f3afbe3fab3a38da68876f77455f449f5fe0179
Move efuse definitions to a separate header file for later
usage with other FW modules.
Change-Id: I2e9465f760d0388c8e5863bc64a4cdc57de2417f
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/47313
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
Use single 64b register for the return value instead of two 32b.
Report an error if caller requested larger than than 64b random
number in a single SMC call.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Ib8756cd3c0808b78c359f90c6f6913f7d16ac360
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/33280
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
This patch forces rx training on 10G ports
as part of comphy_smc call from Linux.
Signed-off-by: Alex Evraev <alexev@marvell.com>
Change-Id: Iebe6ea7c8b21cbdce5c466c8a69b92e9d7c8a8ca
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/30763
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Normally the CP MSS CPU was started at the end of FW load to IRAM at BL2.
However, (especailly in secure boot mode), some bus attributes should be
changed from defaults before the MSS CPU tries to access shared resources.
This patch starts to use CP MSS SRAM for FW load in both secure and
non-secure boot modes.
The FW loader inserts a magic number into MSS SRAM as an indicator of
successfully loaded FS during the BL2 stage and skips releasing the MSS
CPU from the reset state.
Then, at BL31 stage, the MSS CPU is released from reset following the
call to cp110_init function that handles all the required bus attributes
configurations.
Change-Id: Idcf81cc350a086835abed365154051dd79f1ce2e
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46890
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Fixed a bug that the actually bit number was used as a mask to
select LD0 or LD1 fuse
Signed-off-by: Guo Yi <yguo@cavium.com>
Change-Id: I4bec268c3dc2566350b4a73f655bce222707e25b
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/46146
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Setting MSS_SUPPORT to 0 also removes requirement for SCP_BL2
definition.
Images build with MSS_SUPPORT=0 will not include service CPUs
FW and will not support PM, FC and other features implemented
in these FW images.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Idf301ebd218ce65a60f277f3876d0aeb6c72f105
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/37769
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Since the dfx register set is going to be marked as secure expose dfx
secure read and write function via SiP services. In introduced misc_dfx
driver some registers are white-listed so non-secure software can still
access them.
This will allow non-secure word drivers access some white-listed
registers related to e.g.: Sample at reset, efuses, SoC type and
revision ID accesses.
Change-Id: If9ae2da51ab2e6ca62b9a2c940819259bf25edc0
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25055
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Since more drivers which uses dfx register set need to be handled with
use of SiP services, use dedicated and more meaningful name for thermal
SiP services.
Change-Id: Ic2ac27535a4902477df8edc4c86df3e34cb2344f
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/25054
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Since the dfx register set is going to be marked as secure (in order to
protect efuse registers for non secure access), accessing thermal
registers which are part of dfx register set, will not be possible from
lower exception levels. Due to above expose thermal driver as a SiP
service. This will allow Linux and U-Boot thermal driver to initialise
and perform various operations on thermal sensor.
The thermal sensor driver is based on Linux
drivers/thermal/armada_thermal.c.
Change-Id: I4763a3bf5c43750c724c86b1dcadad3cb729e93e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/20581
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Remove an incorrect tabulation in front of an $(error) function call
outside of a recipe, which caused the following text to be displayed:
plat/arm/board/common/board_common.mk:36: *** recipe commences before first target. Stop.
instead of:
plat/arm/board/common/board_common.mk:36: *** "Unsupported ARM_ROTPK_LOCATION value". Stop.
Change-Id: I8592948e7de8ab0c4abbc56eb65a53eb1875a83c
Signed-off-by: Sandrine Bailleux <sandrine.bailleux@arm.com>
UART register definition is the same on MediaTek platforms.
Move uart.h to common folder and remove the duplicate file.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Iea0931dfd606ae4a7ab475b9cb3a08dc6de68b36
The number of ITS have changed from 4 to 1, resulting
in GICR base address change.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Change-Id: I28101f0d1faf9f3c58591b642033c3fd49a275e7
Add support to qemu "max" cpu for both "qemu" ('virt') and
"qemu_sbsa" ('sbsa-ref') platforms.
Change-Id: I36e45c0a3c4e30ba546d2a3cb44dfef11a680305
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
Cortex-A72 support is already enabled for sbsa-ref platform,
so add it also to virt platform for parity.
Change-Id: Ib0a2ce81ef7c0a71ef8dc66dbec179191bf2e6cc
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
The build now gives deprecation warnings for including
drivers/arm/gic/common/gic_common.c directly. Move to including the
common gicv2 sources via gicv2.mk instead - which also matches the
pattern already used for gicv3.
Change-Id: I5332fb52c5801272e5e2bb6111f96087b4894325
Signed-off-by: Leif Lindholm <leif@nuviainc.com>
NT_FW_CONFIG file is meant to be passed from BL31 to be consumed by
BL33, fvp platforms use this to pass measured boot configuration and
the x0 register is used to pass the base address of it.
In case of hafnium used as hypervisor in normal world, hypervisor
manifest is expected to be passed from BL31 and its base address is
passed in x0 register.
As only one of NT_FW_CONFIG or hypervisor manifest base address can be
passed in x0 register and also measured boot is not required for SPM so
disable passing NT_FW_CONFIG.
Signed-off-by: Manish Pandey <manish.pandey2@arm.com>
Change-Id: Ifad9d3658f55ba7d70f468a88997d5272339e53e
Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].
[1] 13f3c5166f ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: I73a079715253699d903721c865d6470d58f6bd30
Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].
[1] 13f3c5166f ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: Id52c0be61a30f453a551385883eaf3cbe32b04b9
Create a dedicated static struct mmc_device_info mmc_info mmc_info
instead of having this in stack.
A boot issue has been seen on some platform when applying patch [1].
[1] 13f3c5166f ("mmc:prevent accessing to the released space in case of wrong usage")
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Change-Id: If5db8857cccec2e677b16a38eb3eeb41628a264c
Refine the function plat_add_sp_images_load_info() by saving the
previous node and only setting its next link when the current node is
valid. This can reduce the check for the next node and simply the
total logic.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: I4061428bf49ef0c3816ac22aaeb2e50315531f88
The traverse flow in function plat_add_sp_images_load_info() will find
the last node in the main load info list, with its
next_load_info==NULL. However this node is still useful and should not
be overridden with SP node info.
The bug will cause below error on RDN2 for spmd enabled:
ERROR: Invalid NT_FW_CONFIG DTB passed
Fix the bug by only setting the next_load_info of the last node in the
original main node list.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Change-Id: Icaee5da1f2d53b29fdd6085a8cc507446186fd57
As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I77994ce387caf0d695986df3d01d414a920978d0
As per the new multi-console framework, updating the JTAG DCC support.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I62cfbb57ae7e454fbc91d1c54aafa6e99f9a35c8
* changes:
plat/sgi: allow usage of secure partions on rdn2 platform
board/rdv1mc: initialize tzc400 controllers
plat/sgi: allow access to TZC controller on all chips
plat/sgi: define memory regions for multi-chip platforms
plat/sgi: allow access to nor2 flash and system registers from s-el0
plat/sgi: define default list of memory regions for dmc620 tzc
plat/sgi: improve macros defining cper buffer memory region
plat/sgi: refactor DMC-620 error handling SMC function id
plat/sgi: refactor SDEI specific macros
Define a GUID that should be used in the header of MM communicate
message originating due to a dmc620 ECC error interrupt. So the use
of SMC ID in 'sgi_ras_ev_map' to represent the interrupt event is
removed.
In addition to this, update the dmc620 error record data structure to
use aux_data to indicate the dmc620 instance number on which the ECC
error interrupt occurred.
Signed-off-by: Omkar Anand Kulkarni <omkar.kulkarni@arm.com>
Change-Id: I18c8ef5ba6483bb1bce6464ee9be0c2aabec4baa
Add the secure partition mmap table and the secure partition boot
information to support secure partitions on RD-N2 platform. In addition
to this, add the required memory region mapping for accessing the
SoC peripherals from the secure partition.
Signed-off-by: Omkar Anand Kulkarni <omkar.kulkarni@arm.com>
Change-Id: I2c75760d6c8c3da3ff4885599be420e924aeaf3c
A TZC400 controller is placed inline on DRAM channels and regulates
the secure and non-secure accesses to both secure and non-secure
regions of the DRAM memory. Configure each of the TZC controllers
across the Chips.
For use by secure software, configure the first chip's trustzone
controller to protect the upper 16MB of the memory of the first DRAM
block for secure accesses only. The other regions are configured for
non-secure read write access. For all the remote chips, all the DRAM
regions are allowed for non-secure read and write access.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I809f27eccadfc23ea0ef64e2fd87f95eb8f195c1
On a multi-chip platform, the boot CPU on the first chip programs the
TZC controllers on all the remote chips. Define a memory region map for
the TZC controllers for all the remote chips and include it in the BL2
memory map table.
In addition to this, for SPM_MM enabled multi-chip platforms, increase
the number of mmap entries and xlat table counts for EL3 execution
context as well because the shared RAM regions and GIC address space of
remote chips are accessed.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I6f0b5fd22f9f28046451e382eef7f1f9258d88f7
For multi-chip platforms, add a macro to define the memory regions on
chip numbers >1 and its associated access permissions. These memory
regions are marked with non-secure access.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: If3d6180fd8ea61f45147c39d3140d694abf06617
Allow the access of system registers and nor2 flash memory region
from s-el0. This allows the secure parititions residing at s-el0
to access these memory regions.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I3887a86770de806323fbde0d20fdc96eec6e0c3c
Define a default DMC-620 TZC memory region configuration and use it to
specify the TZC memory regions on sgi575, rdn1edge and rde1edge
platforms. The default DMC-620 TZC memory regions are defined
considering the support for secure paritition as well.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: Iedee3e57d0d3de5b65321444da51ec990d3702db
Remove the 'ARM_' prefix from the macros defining the CPER buffer memory
and replace it with 'CSS_SGI_' prefix. These macros are applicable only
for platforms supported within plat/sgi. In addition to this, ensure
that these macros are defined only if the RAS_EXTENSION build option is
enabled.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I44df42cded18d9d3a4cb13e5c990e9ab3194daee
The macros defining the SMC function ids for DMC-620 error handling are
listed in the sgi_base_platform_def.h header file. But these macros are
not applicable for all platforms supported under plat/sgi. So move these
macro definitions to sgi_ras.c file in which these are consumed. While
at it, remove the AArch32 and error injection function ids as these are
unused.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I249b54bf4c1b1694188a1e3b297345b942f16bc9
The macros specific to SDEI defined in the sgi_base_platform_def.h are
not applicable for all the platforms supported by plat/sgi. So refactor
the SDEI specific macros into a new header file and include this file on
only on platforms it is applicable on.
Signed-off-by: Thomas Abraham <thomas.abraham@arm.com>
Change-Id: I0cb7125334f02a21cae1837cdfd765c16ab50bf5
Broadcom I2C controller driver. Follwoing API's are supported:-
- i2c_init() Intialize ethe I2C controller
- i2c_probe()
- i2c_set_bus_speed() Set the I2C bus speed
- i2c_get_bus_speed() Get the current bus speed
- i2c_recv_byte() Receive one byte of data.
- i2c_send_byte() Send one byteof data
- i2c_read_byte() Read single byte of data
- i2c_read() Read multiple bytes of data
- i2c_write_byte Write single byte of data
- i2c_write() Write multiple bytes of data
This driver is verified by reading the DDR SPD data.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Change-Id: I2d7fe53950e8b12fab19d0293020523ff8b74e13
When the BL31 for the Allwinner H616 runs in DRAM, we need to make sure
we tell the non-secure world about the memory region it uses.
Add a reserved-memory node to the DT, which covers the area that BL31
could occupy. The "no-map" property will prevent OSes from mapping
the area, so there would be no speculative accesses.
Change-Id: I808f3e1a8089da53bbe4fc6435a808e9159831e1
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ENABLE_PIE (position independent executable) is default on K3
platform to handle variant RAM configurations in the system. This,
unfortunately does cause confusion while reading the code, so, lets
make things explicit by selecting 0x0 as the "SEC_SRAM_BASE" out of
which we compute the BL31_BASE depending on usage.
Lets also document a warning while at it to help folks copying code
over to a custom K3 platform and optimizing size by disabling PIE to
modify the defaults.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I8e67a9210e907e266ff6a78ba4d02e3259bb2b21
Lets cast our macros to the right types and reduce a few MISRA
warnings.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I0dc06072713fe7c9440eca0635094c5f3ceb7f1c
We compute BL31_END - BL31_START on the fly, which is basically
BL31_SIZE. Lets just use the BL31_SIZE directly so that we dont
complicate PIE relocations when actual address is +ve and -ve offsets
relative to link address.
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5e14906381d2d059163800d39798eb39c42da4ec
Since we are using static xlat tables, we need to account for exact
count of table entries we are actually using.
peripherals usart, gic, gtc, sec_proxy_rt, scfg and data account for 6 entries
and are constant, however, we also need to account for:
bl31 full range, codebase, ro_data as additional 3 region
With USE_COHERENT_MEM we do add in 1 extra region as well.
This implies that we will have upto 9 or 10 regions based on
USE_COHERENT_MEM usage. Vs we currently define 8 regions.
This gets exposed with DEBUG=1 and assert checks trigger, which for some
reason completely escaped testing previously.
ASSERT: lib/xlat_tables_v2/xlat_tables_core.c:97
BACKTRACE: START: assert
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I962cdfc779b4eb3b914fe1c46023d50bc289e6bc
We actually have additional table entries than what we accounted for in
our size. MAX_XLAT_TABLES is 8, but really we could be using upto 10
depending on the platform. So, we need an extra 8K space in.
This gets exposed with DEBUG=1 and assert checks trigger, which for some
reason completely escaped testing previously.
ASSERT: lib/xlat_tables_v2/xlat_tables_core.c:97
BACKTRACE: START: assert
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I5c5d04440ef1fccfaf2317066f3abbc0ec645903
The new Allwinner H616 SoC lacks the management controller and the secure
SRAM A2, so we need to tweak the memory map quite substantially:
We run BL31 in DRAM. Since the DRAM starts at 1GB, we cannot use our
compressed virtual address space (max 256MB) anymore, so we revert to
the full 32bit VA space and use a flat mapping throughout all of it.
The missing controller also means we need to always use the native PSCI
ops, using the CPUIDLE hardware, as SCPI and suspend depend on the ARISC.
Change-Id: I77169b452cb7f5dc2ef734f3fc6e5d931749141d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In preparation for changing the memory map, express the locations of the
various code and data pieces more dynamically, allowing SoCs to override
the memmap later.
Also prepare for the SCP region to become optional.
No functional change.
Change-Id: I7ac01e309be2f23bde2ac2050d8d5b5e3d6efea2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The code to power the current core off when SCPI is not available is now
different for the two supported SoC families.
To make adding new platforms easier, move sunxi_cpu_power_off_self()
into the SoC directory, so we don't need to carry definitions for both
methods for all SoCs.
On the H6 we just need to trigger the CPUIDLE hardware, so can get rid
of all the code to program the ARISC, which is now only needed for the
A64 version.
Change-Id: Id2a1ac7dcb375e2fd021b441575ce86b4d7edf2c
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the existing SoCs we support, we use SEPARATE_NOBITS_REGION, to move
some parts of the data into separate memory regions (to save on the SRAM
A2 we are loaded into).
For the upcoming H616 platform this is of no concern (we run in DRAM),
so make this flag a platform choice instead.
Change-Id: Ic01d49578c6274660f8f112bd23680d3eca3be7a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The upcoming refactoring to support the new H616 SoCs will push the A64
build over the edge, by using more than the 48KB of SRAM available.
To reduce the code size, set some libfdt options that aim to reduce
sanity checks (for saving code space):
- ASSUME_LATEST: only allow v17 DTBs (as created by dtc)
- ASSUME_NO_ROLLBACK: don't prepare for failed DT additions
- ASSUME_LIBFDT_ORDER: assume sane ordering, as done by dtc
Change-Id: I12c93ec09e7587c5ae71e54947f817c32ce5fd6d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
* changes:
nxp lx2160a-aqds: new plat based on soc lx2160a
NXP lx2160a-rdb: new plat based on SoC lx2160a
nxp lx2162aqds: new plat based on soc lx2160a
nxp: errata handling at soc level for lx2160a
nxp: make file for loading additional ddr image
nxp: adding support of soc lx2160a
nxp: deflt hdr files for soc & their platforms
nxp: platform files for bl2 and bl31 setup
nxp: warm reset support to retain ddr content
nxp: nv storage api on platforms
nxp: supports two mode of trusted board boot
nxp: fip-handler for additional fip_fuse.bin
nxp: fip-handler for additional ddr-fip.bin
nxp: image loader for loading fip image
nxp: svp & sip smc handling
nxp: psci platform functions used by lib/psci
nxp: helper function used by plat & common code
nxp: add data handler used by bl31
nxp: adding the driver.mk file
nxp-tool: for creating pbl file from bl2
nxp: adding the smmu driver
nxp: cot using nxp internal and mbedtls
nxp:driver for crypto h/w accelerator caam
nxp:add driver support for sd and emmc
nxp:add qspi driver
nxp: add flexspi driver support
nxp: adding gic apis for nxp soc
nxp: gpio driver support
nxp: added csu driver
nxp: driver pmu for nxp soc
nxp: ddr driver enablement for nxp layerscape soc
nxp: i2c driver support.
NXP: Driver for NXP Security Monitor
NXP: SFP driver support for NXP SoC
NXP: Interconnect API based on ARM CCN-CCI driver
NXP: TZC API to configure ddr region
NXP: Timer API added to enable ARM generic timer
nxp: add dcfg driver
nxp:add console driver for nxp platform
tools: add mechanism to allow platform specific image UUID
tbbr-cot: conditional definition for the macro
tbbr-cot: fix the issue of compiling time define
cert_create: updated tool for platform defined certs, keys & extensions
tbbr-tools: enable override TRUSTED_KEY_CERT
SoC erratas are handled as part of this commit.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I06f7594d19cc7fc89fe036a8a255300458cb36dd
- NXP SoC lx2160a needs additional ddr_fip.bin.
- There are three types of ddr image that can be created:
-- ddr_fip.mk for creating fip_ddr.bin image for normal boot.
-- ddr_fip_sb.mk for creating fip_ddr_sec.bin image for NXP CSF based
CoT/secure boot.
-- ddr_fip_tbbr.mk for creating fip_ddr_sec.bin image for MBEDTLS
CoT/secure boot.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I24bff8d489f72da99f64cb79b2114faa9423ce8c
* NXP SoC is 16 A-72 core SoC.
* SoC specific defines are defined in:
- soc.def
- soc.h
* Called for BL2 and BL31 setup, SoC specific setup are implemented in:
- soc.c
* platform specific helper functions implemented at:
- aarch64/lx2160a_helpers.S
* platform specific functions used by 'plat/nxp/commpon/psci',
etc. are implemented at:
- aarch64/lx2160a.S
* platform specific implementation for handling PSCI_SYSTEM_RESET2:
- aarch64/lx2160a_warm_rst.S
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ib40086f9d9079ed9b22967baff518c6df9f408b8
For NXP platforms:
- Setup files for BL2 and BL31
- Other supporting files.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I36a1183a0652701bdede9e02d41eb976accbb017
NXP: Added warm reset handler to handle SMC PSCI_SYSTEM_RESET2
raised from kernel (> 5.4).
As part of first cold boot, DDR training data is stored in NV storage.
As part of this SMC handling, following things are done:
- DDR is put in self-refresh mode to retain the content of DDR.
- Reset cause is saved.
- Reset is triggered.
On next boot to last warm-reset, DDR training is restored from
the NV storage.
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I8e4fb0824887af49e959c93825e2ab0ba887fc9d
NV storage API(s) for NXP platforms, supported on:
- flexspi-nor
- SecMon - General Purpose Registers at Low-Power section,
retains their content if backed by coined battery.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Id65dee4f28e7d6d2024407030039de33ebe0fa05
NXP SoC supports two TBB mode:
- MBED_TLS based
-- ROTK key hash is placed as part of the BL2 binary at section:
--- .rodata.nxp_rotpk_hash
-- Supporting non-volatile counter via SFP.
-- platform function used by TFA common authentication code.
- NXP CSF based
-- ROTK key deployment vary from MBEDTLS
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ib0f0bf024fd93de906c5d4f609383ae9e02b2fbc
All of the NXP SoC, needs fip_fuse image to be
loaded additionally as part of preparation for Trusted board boot
- fip_fuse.bin contains an image for auto fuse provisioning.
- Auto fuse provisioning is based on the input file with values for:
-- SRK Hash
-- OTPMK
-- misc. refer board manual for more details.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I26d4024fefe352d967ca120191f784f1f47aa9d1
Few of the NXP SoC like LX2160A, needs ddr-phy images to be
loaded additionally before DDR initialization
- fip_ddr.bin is created containing upto 6 ddr images.
- With TRUSTED_BOARD_BOOT = 1, fip_ddr.bin is authenticated
first before loading and starting DDR initialization.
- To successfully compile this image, platform-defined header files
needs to be defined:
-- include/common/tbbr/tbbr_img_def.h uses:
--- plat_tbbr_img_def.h: platform specific new FIP image macros.
-- include/tools/share/firmware_image_package.h uses:
--- plat_def_fip_uuid.h: platform specific new UUID macros.
---- Added UUID for DDR images to create FIP-DDR.
---- Added UUID for FUSE provisioning images to create FIP-fuse.
-- include/tools/share/tbbr_oid.h uses:
--- platform_oid.h: platform specific new OID macros.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Icbcf1673a8c398aae98680b5016f4276b4864b91
function load_img(), is dependent on:
- Recursively calling load_image() defined in common/bl_common.c
- for each image in the fip.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I57ca4b666cd1b0b992b7c0fc2a4260b558c0e2a9
bl31-data file written in assembly helps to manage data at bl31.
Signed-off-by: rocket <rod.dorris@nxp.com>
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: Ic3ace03364648cc1174bb05b5b334b9ccdaaa4ed
This works even on SoCs that do not have an ARISC, and it avoids
clobbering whatever ARISC firmware might be running.
Change-Id: I9f2fed597189bb387de79e8e76a7da3375e1ee91
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adds bl2 with FIP to the build required for mbed Linux booting where
we do:
BootROM -> SPL -> BL2 -> OPTEE -> u-boot
If NEED_BL2 is specified then BL2 will be built and BL31 will have
its address range modified upwards to accommodate. BL31 must be
loaded from a FIP in this case.
If NEED_BL2 is not specified then the current BL31 boot flow is
unaffected and u-boot SPL will load and execute BL31 directly.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I655343b3b689b1fc57cfbedda4d3dc2fbd549a96
This patch enables Trusted Boot on the i.MX8MM with BL2 doing image
verification from a FIP prior to hand-over to BL31.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I3c22783a5c49544d0bace8ef3724784b9b7cc64a
Adds a number of definitions consistent with the established WaRP7
equivalents specifying number of io_handles and block devices.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: If1d7ef1ad3ac3dfc860f949392c7534ce8d206e3
Allows for exporting of FIP related methods cleanly in a private header.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Change-Id: I8523f1370312ed22ff7ca710cd916be52f725e3c
TZC400 is configured to raise an interrupt in case of faulty access.
Call the new added tzc400_it_handler, in case this interrupt occurs.
Change-Id: Iaf4fa408a8eff99498042e11e2d6177bad39868c
Signed-off-by: Yann Gautier <yann.gautier@st.com>
On STM32MP15, only filters 0 and 1 are used.
Use TZC_400_REGION_ATTR_FILTER_BIT() macro for those 2 filters 0 and 1
instead of U(3).
Change-Id: Ibc61823842ade680f59d5b66b8db59b6a30080e4
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Addresses the deprecation warning produced by
drivers/arm/gic/common/gic_common.c.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Change-Id: I1a3ff4835d0f94c74b405db10622e99875ded82b
BIT24 of IPI command header is used to determine if caller is
secure or non-secure.
Mark BIT24 of IPI command header as non-secure if SMC caller
is non-secure.
Signed-off-by: Tejas Patel <tejas.patel@xilinx.com>
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Change-Id: Iec25af8f4b202093f58e858ee47cd9cd46890267
Versal is a72 based that's why there is no reason to build low level
assemble code for a53.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: Iff9cf2582102d951825b87fd9af18e831ca717d6
The FF-A v1.0 spec allows two configurations for the number of EC/vCPU
instantiated in a Secure Partition:
-A MultiProcessor (MP) SP instantiates as many ECs as the number of PEs.
An EC is pinned to a corresponding physical CPU.
-An UniProcessor (UP) SP instantiates a single EC. The EC is migrated to
the physical CPU from which the FF-A call is originating.
This change permits exercising the latter case within the TF-A-tests
framework.
Signed-off-by: Olivier Deprez <olivier.deprez@arm.com>
Change-Id: I7fae0e7b873f349b34e57de5cea496210123aea0
Compiling BL31 for the Rockchip platform now produces a message about
the deprecation of gic_common.c.
Follow the advice and use include gicv2.mk instead.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Change-Id: I396b977d57975dba27cfed801ad5264bbbde2b5e
The case for value "VCOREFS_SMC_CMD_INIT" is not
terminated by a "break" statement.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Change-Id: I56cc7c1648e101c0da6e77e592e6edbd5d37724e
1 Only enable domain D0 and D1:PCIe access 0xC0000000~0xC4000000;
2 Only enable domain D0 and D3(SCP) access 0x50000000~0x51400000;
Signed-off-by: Xi Chen <xixi.chen@mediatek.com>
Change-Id: Ic4f9e6d85bfd1cebdb24ffc1d14309c89c103b2a
Low Power Management (LPM) helps find a suitable configuration
for letting system entering idle or suspend with the most
resources off.
Change-Id: Ie6a7063b666cf338cff5bc972c9025b26de482eb
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Add support for ZU43DR, ZU46DR and ZU47DR to the list of zynqmp
devices. The ZU43DR, ZU46DR and ZU47DR RFSoC silicon id values are
0x7d, 0x78 and 0x7f.
Signed-off-by: Sandeep Gundlupet Raju <sandeep.gundlupet-raju@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Change-Id: I566f707116d83475de7c87a6004ca96bf7bccebe
This commit fixes the wrong memory type, secure NOR flash
shall be mapped as MT_DEVICE.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: I9c9ed51675d84ded675bb56b2e4ec7a08184c602
sbsa-ref in QEMU may create up to 512 cores.
This commit prepares the MP information to support 512 cores.
The number of xlat tables for spm_mm is also increased.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Change-Id: I2788eaf6d14e188e9b5d1102d359b2899e02df7c
* changes:
plat/marvell/armada: cleanup MSS SRAM if used for copy
plat/marvell: cn913x: allow CP1/CP2 mapping at BLE stage
plat/marvell/armada/common/mss: use MSS SRAM in secure mode
include/drivers/marvell/mochi: add detection of secure mode
plat/marvell: fix SPD handling in dram port
marvell: drivers: move XOR0/1 DIOB from WIN 0 to 1
drivers/marvell/mochi: add support for cn913x in PCIe EP mode
drivers/marvell/mochi: add missing stream IDs configurations
plat/marvell/armada/a8k: support HW RNG by SMC
drivers/rambus: add TRNG-IP-76 driver
This patch cleans up the MSS SRAM if it was used for MSS image
copy (secure boot mode).
Change-Id: I23f600b512050f75e63d59541b9c21cef21ed313
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/30099
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Map IO WIN to CP1 and CP2 at all stages including the BLE.
Do not map CP1/CP2 if CP_NUM is lower than 2 and 3 accordingly.
This patch allows access to CP1/CP2 internal registers at
BLE stage if CP1/CP2 are connected.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: Icf9ffdf2e9e3cdc2a153429ffd914cc0005f9eca
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/36939
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Yi Guo <yi.guo@cavium.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
The CP MSS IRAM is only accessible by CM3 CPU and MSS DMA.
In secure boot mode the MSS DMA is unable to directly load
the MSS FW image from DRAM to IRAM.
This patch adds support for using the MSS SRAM as intermediate
storage. The MSS FW image is loaded by application CPU into the
MSS SRAM first, then transferred to MSS IRAM by MSS DMA.
Such change allows the CP MSS image load in secure mode.
Change-Id: Iee7a51d157743a0bdf8acb668ee3d599f760a712
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaszczyk@marvell.com>
Removing the custom crash implementation and use
plat/common/aarch64/crash_console_helpers.S.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Change-Id: I045d42eb62bcaf7d1e18fbe9ab9fb9470e800215
* changes:
allwinner: Split native and SCPI-based PSCI implementations
allwinner: psci: Improve system shutdown/reset sequence
allwinner: psci: Drop .pwr_domain_pwr_down_wfi callback
allwinner: Separate code to power off self and other CPUs
Rename rd_n1e1_edge_scmi_plat_info array to plat_rd_scmi_info as the
same array is used to provide SCMI platform info across mulitple RD
platforms and is not resitricted to only RD-N1 and RD-E1 platforms.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I42ba33e0afa3003c731ce513c6a5754b602ec01f
Now that we have a framework for the SMCCC TRNG interface, and the
existing Juno entropy code has been prepared, add the few remaining bits
to implement this interface for the Juno Trusted Entropy Source.
We retire the existing Juno specific RNG interface, and use the generic
one for the stack canary generation.
Change-Id: Ib6a6e5568cb8e0059d71740e2d18d6817b07127d
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Juno Trusted Entropy Source has a bias, which makes the generated
raw numbers fail a FIPS 140-2 statistic test.
To improve the quality of the numbers, we can use the CPU's CRC
instructions, which do a decent job on conditioning the bits.
This adds a *very* simple version of arm_acle.h, which is typically
provided by the compiler, and contains the CRC instrinsics definitions
we need. We need the original version by using -nostdinc.
Change-Id: I83d3e6902d6a1164aacd5060ac13a38f0057bd1a
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
NXP specifc macro SET_NXP_MAKE_FLAG is added.
NXP has pool of multiple IPs. This macro helps:
- In soc.mk, this macro help the selected IP source files to be included
for that SoC.
-- The set of IPs required for one NXP SoC is different to the set of IPs
required by another NXP SoC.
- For the same SoC,
-- For one feature, the IP may be required in both BL2 and BL31.
-- Without the above feature, that IP may be required in one.
This macro help in selecting the inclusion of source and header files to:
--- BL2 only
--- BL31 only
--- COMM (used by BL2 and BL31)
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Change-Id: I2cdb13b89aa815fc5219cf8bfb9666d0a9f78765
Currently we use the Juno's TRNG hardware entropy source to initialise
the stack canary. The current function allows to fill a buffer of any
size, but we will actually only ever request 16 bytes, as this is what
the hardware implements. Out of this, we only need at most 64 bits for
the canary.
In preparation for the introduction of the SMCCC TRNG interface, we
can simplify this Juno specific interface by making it compatible with
the generic one: We just deliver 64 bits of entropy on each call.
This reduces the complexity of the code. As the raw entropy register
readouts seem to be biased, it makes sense to do some conditioning
inside the juno_getentropy() function already.
Also initialise the TRNG hardware, if not already done.
Change-Id: I11b977ddc5417d52ac38709a9a7b61499eee481f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DRAM port code issues a dummy write to SPD page-0 i2c address
in order to select this page for the forthcoming read transaction.
If the write buffer length supplied to i2c_write is not zero, this
call is translated to 2 bus transations:
- set the target offset
- write the data to the target
However no actual data should be transferred to SPD page-0 in order
to select it. Actually, the second transation never receives an ACK
from the target device, which caused the following error report:
ERROR: Status 30 in write transaction
This patch sets the buffer length in page-0 select writes to zero,
leading to bypass the data transfer to the target device.
Issuing the target offset command to SPD page-0 address effectively
selects this page for the read operation.
Change-Id: I4bf8e8c09da115ee875f934bc8fbc9349b995017
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: https://sj1git1.cavium.com/24387
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Moti Buskila <motib@marvell.com>
Add initialization for TRNG-IP-76 driver and support SMC call
0xC200FF11 used for reading HW RNG value by secondary bootloader
software for KASLR support.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Change-Id: I1d644f67457b28d347523f8a7bfc4eacc45cba68
Reviewed-on: https://sj1git1.cavium.com/c/IP/SW/boot/atf/+/32688
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Update TZC base address to align with the recent changes in the platform
memory map.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Change-Id: I0d0ad528a2e236607c744979e1ddc5c6d426687a
Currently, BLs are mapping the GIC memory region as read-write
for all cores on boot-up.
This opens up the security hole where the active core can write
the GICR frame of fused/inactive core. To avoid this issue, disable
the GICR frame of all inactive cores as below:
1. After primary CPU boots up, map GICR region of all cores as
read-only.
2. After primary CPU boots up, map its GICR region as read-write
and initialize its redistributor interface.
3. After secondary CPU boots up, map its GICR region as read-write
and initialize its redistributor interface.
4. All unused/fused core's redistributor regions remain read-only and
write attempt to such protected regions results in an exception.
As mentioned above, this patch offers only the GICR memory-mapped
region protection considering there is no facility at the GIC IP
level to avoid writing the redistributor area.
These changes are currently done in BL31 of Arm FVP and guarded under
the flag 'FVP_GICR_REGION_PROTECTION'.
As of now, this patch is tested manually as below:
1. Disable the FVP cores (core 1, 2, 3) with core 0 as an active core.
2. Verify data abort triggered by manually updating the ‘GICR_CTLR’
register of core 1’s(fused) redistributor from core 0(active).
Change-Id: I86c99c7b41bae137b2011cf2ac17fad0a26e776d
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
GIC memory region is not getting used in BL1 and BL2.
Hence avoid its mapping in BL1 and BL2 that freed some
page table entries to map other memory regions in the
future.
Retains mapping of CCN interconnect region in BL1 and BL2
overlapped with the GIC memory region.
Change-Id: I880dd0690f94b140e59e4ff0c0d436961b9cb0a7
Signed-off-by: Manish V Badarkhe <Manish.Badarkhe@arm.com>
So far the ARM platform Makefile would require that RESET_TO_BL31 is set
when we ask for the ARM_LINUX_KERNEL_AS_BL33 feature.
There is no real technical reason for that, and the one place in the
code where this was needed has been fixed.
Remove the requirement of those two options to be always enabled
together.
This enables the direct kernel boot feature for the Foundation FVP
(as described in the documentation), which requires a BL1/FIP
combination to boot, so cannot use RESET_TO_BL31.
Change-Id: I6814797b6431b6614d684bab3c5830bfd9481851
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we have the somewhat artifical limitation of
ARM_LINUX_KERNEL_AS_BL33 only being used together with RESET_TO_BL31.
However there does not seem to be a good technical reason for that,
it was probably just to differentate between two different boot flows.
Move the initial register setup for ARM_LINUX_KERNEL_AS_BL33 out of the
RESET_TO_BL31 #ifdef, so that we initialise the registers in any case.
This allows to use a preloaded kernel image when using BL1 and FIP.
Change-Id: I832df272d3829f077661f4ee6d3dd9a276a0118f
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The structure has been modified to specify the memory
size in bytes instead of Gigabytes.
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Signed-off-by: Chandni Cherukuri <chandni.cherukuri@arm.com>
Change-Id: I3384677d79af4f3cf55d3c353b6c20bb827b5ae7
This patch removes the Neoverse N1 CPU errata workaround for
bug 1542419 as the bug is not present in Rainier R0P0 core.
Change-Id: Icaca299b13ef830b2ee5129576aae655a6288e69
Signed-off-by: Manoj Kumar <manoj.kumar3@arm.com>
Secure pl061 qemu driver allows to rize the GPIO pin
from the secure world to reboot and power down
virtual machine.
Do not define secure-gpio for sbsa-ref platform due to
reboot is done via sbsa-ec watchdog.
Signed-off-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Change-Id: I508d7c5cf4c75cb169b34b00682a76f6761d3869
The NUM_APID value was derived from kernel device tree sources, but I
made a conversion mistake: the amount of bytes in the APID map is the
total size of the "core" register range (0x1100) minus the offset of the
APID map in that range (0x900). This is of course 0x1100 - 0x900 = 0x800
and not 0x200, so the amount of 4-byte integers it can fit is not 0x80
but 0x200. Fix this and make the math more explicit so it can be more
easily factored out and adjusted if that becomes necessary for a future
SoC.
Also fix a dangerous typo in REG_APID_MAP() where the macro would
reference a random variable `i` rather than its argument (`apid`), and
we just got lucky that the only caller in the current code happened to
pass in a variable called `i` as that argument.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I049dd044fa5aeb65be0e7b12150afd6eb4bac0fa
Increase the core count and add respective entries in DTS.
Add Klein assembly file to cpu sources for core initialization.
Add SCMI entries for cores.
Signed-off-by: Avinash Mehta <avinash.mehta@arm.com>
Change-Id: I14dc1d87df6dcc8d560ade833ce1f92507054747
When building TF-A with USE_ROMLIB=1 and -j make options, the build fails with the following error:
make[1]: *** No rule to make target '/build/juno/debug/romlib/romlib.bin', needed by 'bl1_romlib.bin'.
This patch fixes that issue.
Signed-off-by: Zelalem <zelalem.aweke@arm.com>
Change-Id: I0cca416f3f50f400759164e0735c2d6b520ebf84
* changes:
docs: marvell: Update info about WTMI_IMG option
plat: marvell: armada: a3k: Remove unused variable WTMI_SYSINIT_IMG from Makefile
plat: marvell: armada: Show informative build messages and blank lines
plat: marvell: armada: Move definition of mrvl_flash target to common marvell_common.mk file
plat: marvell: armada: a3k: Use $(Q) instead of @
plat: marvell: armada: a3k: Add a new target mrvl_uart which builds UART image
plat: marvell: armada: a3k: Build UART image files directly in $(BUILD_UART) subdirectory
plat: marvell: armada: a3k: Build intermediate files in $(BUILD_PLAT) directory
plat: marvell: armada: a3k: Correctly set DDR_TOPOLOGY and CLOCKSPRESET for WTMI
plat: marvell: armada: a3k: Allow use of the system Crypto++ library
docs: marvell: Update info about WTP and MV_DDR_PATH parameters
plat: marvell: armada: a3k: Add checks that WTP, MV_DDR_PATH and CRYPTOPP_PATH are correctly defined
docs: marvell: Update mv-ddr-marvell and A3700-utils-marvell branches
* changes:
allwinner: Leave CPU power alone during BL31 setup
allwinner: psci: Invert check in .validate_ns_entrypoint
allwinner: psci: Drop MPIDR check from .pwr_domain_on
allwinner: psci: Drop .get_node_hw_state callback
AMU counters are used for monitoring the CPU performance. RD-N2 platform
has architected AMU available for each core. Enable the use of AMU by
non-secure OS for supporting the use of counters for processor
performance control (ACPI CPPC).
Change-Id: I5cc749cf63c18fc5c7563dd754c2f42990a97e23
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
AMU counters are used for monitoring the CPU performance. RD-V1 platform
has architected AMU available for each core. Enable the use of AMU by
non-secure OS for supporting the use of counters for processor
performance control (ACPI CPPC).
Change-Id: I4003d21407953f65b3ce99eaa8f496d6052546e0
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
Some of the PSCI platform callbacks were restricted on RD-V1 platform
because the idle was not functional. Now that it is functional, remove
all the restrictions on the use PSCI platform callbacks.
Change-Id: I4cb97cb54de7ee166c30f28df8fea653b6b425c7
Signed-off-by: Pranav Madhu <pranav.madhu@arm.com>
It does not have to be supported by the current shell used in Makefile.
Replace it by a simple echo with implicit newline.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I97fe44986ac36d3079d5258c67f0c9184537e7f0
This change separates building of flash and UART images, so it is possible
to build only one of these images. Also this change allows make to build
them in parallel.
Target mrvl_flash now builds only flash image and mrvl_uart only UART
image. This change reflects it also in the documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ie9ce4538d52188dd26d99dfeeb5ad171a5b818f3
This removes need to move files and also allows to build uart and flash
images in parallel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I13bea547d7849615e1c1e11d333c8c99e568d3f6
Currently a3700_common.mk makefile builds intermediate files in TF-A top
level directory and also outside of the TF-A tree. This change fixes this
issue and builds all intermediate files in $(BUILD_PLAT) directory.
Part of this change is also removal of 'rm' and 'mv' commands as there is
no need to remove or move intermediate files from outside of the TF-A build
tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I72e3a3024bd3fdba1b991a220184d750029491e9
When building WTMI image we need to correctly set DDR_TOPOLOGY and
CLOCKSPRESET variables which WTMI build system expect. Otherwise it use
default values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: Ib83002194c8a6c64a2014899ac049bd319e1652f
This change introduces two new A3720 parameters, CRYPTOPP_LIBDIR and
CRYPTOPP_INCDIR, which can be used to specify directory paths to
pre-compiled Crypto++ library and header files.
When both new parameters are specified then the source code of Crypto++ via
CRYPTOPP_PATH parameter is not needed. And therefore it allows TF-A build
process to use system Crypto++ library.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I6d440f86153373b11b8d098bb68eb7325e86b20b
These variables must contain a path to a valid directory (not a file) which
really exists. Also WTP and MV_DDR_PATH must point to either a valid Marvell
release tarball or git repository.
Signed-off-by: Pali Rohár <pali@kernel.org>
Change-Id: I1ad80c41092cf3ea6a625426df62b7d9d6f37815
Now that we have split the native and the SCPI version of the PSCI ops,
we can introduce build options to compile in either or both of them.
If one version is not compiled in, some stub functions make sure the
common code still compiles and makes the right decisions.
By default both version are enabled (as before), but one of them can be
disabled on the make command line, or via a platform specific Makefile.
Change-Id: I0c019d8700c0208365eacf57809fb8bc608eb9c0
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
In order to keep SCP firmware as optional, the original, limited native
PSCI implementation was kept around as a fallback. This turned out to be
a good decision, as some newer SoCs omit the ARISC, and thus cannot run
SCP firmware.
However, keeping the two implementations in one file makes things
unnecessarily messy. First, it is difficult to compile out the
SCPI-based implementation where it is not applicable. Second the check
is done in each callback, while scpi_available is only updated at boot.
This makes the individual callbacks unnecessarily complicated.
It is cleaner to provide two entirely separate implementations in two
separate files. The native implementation does not support any kind of
CPU suspend, so its callbacks are greatly simplified. One function,
sunxi_validate_ns_entrypoint, is shared between the two implementations.
Finally, the logic for choosing between implementations is kept in a
third file, to provide for platforms where only one implementation is
applicable and the other is compiled out.
Change-Id: I4914f07d8e693dbce218e0e2394bef15c42945f8
Signed-off-by: Samuel Holland <samuel@sholland.org>
- When the SCPI shutdown/reset command returns success, the SCP is
still waiting for the CPU to enter WFI. Do that.
- Peform board-level poweroff before CPU poweroff. If there is a PMIC
available, it will turn everything off including the CPUs, so doing
CPU poweroff first is a waste of cycles.
- During poweroff, attempt to turn off the local CPU using the ARISC.
This should use slightly less power than just an infinite WFI.
- Drop the WFI in the reset failure path. The panic will hang anyway.
Change-Id: I897efecb3fe4e77a56041b97dd273156ec51ef8e
Signed-off-by: Samuel Holland <samuel@sholland.org>
When operating on the local cpu, sunxi_cpu_power_off_self() only "arms"
the ARISC to perform the power-off process; the SCP waits for the CPU to
enter WFI before acutally powering it off. Since this matches the
expected split between .pwr_domain_off and .pwr_domain_pwr_down_wfi, we
can move the sunxi_cpu_power_off_self() call to sunxi_pwr_domain_off().
Since that change makes sunxi_pwr_down_wfi() equivalent to the default
implementation, the callback is no longer needed.
Change-Id: I7d65f66c550d1c69fa5e9945affd7a25b3d3ef42
Signed-off-by: Samuel Holland <samuel@sholland.org>
Currently, sunxi_cpu_off() has two separate code paths: one for the
local CPU, and one for other CPUs. Let's split them in to two functions.
This actually simplifies things, because all callers either operate on
the local CPU only (sunxi_pwr_down_wfi()) or other CPUs only
(sunxi_cpu_power_off_others()). This avoids needing a second MPIDR read
to choose the appropriate code path.
Change-Id: I55de85025235cc95466bfa106831fc4c2368f527
Signed-off-by: Samuel Holland <samuel@sholland.org>
Disabling secondary CPUs during boot is unnecessary because the other
CPUs are already in reset, and it saves an entirely insignificant amount
of power. Let's remove this bit of code that was added mostly "because
we can", and along with it remove an unconditional dependency on the CPU
ops functions.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Change-Id: Ia77a1b722da6ba989c3992b656a6cde3f2238fd7
Checking the exceptional case and letting the success case fall through
is not only more idiomatic, but it also allows adding more exceptional
cases in the future, such as a check for overlapping secure DRAM.
Change-Id: I720441a6a8853fd7f211ebe851f14d921a6db03d
Signed-off-by: Samuel Holland <samuel@sholland.org>
This duplicated the logic in psci_validate_mpidr() which was already
called from psci_cpu_on().
Change-Id: I96ee92f1ce3e9cc2985b4e229ba86ebd27b79915
Signed-off-by: Samuel Holland <samuel@sholland.org>
This optional PSCI function was only implemented when SCPI was
available. However, the underlying SCPI function is not able to fulfill
the necessary contract. First, the SCPI protocol has no way to represent
HW_STANDBY at the CPU power level. Second, the SCPI implementation
maintains its own logical view of power states, and its implementation
of SCPI_CMD_GET_CSS_POWER_STATE does not actually query the hardware.
Thus it cannot provide "the physical view of power state", as required
for this function by the PSCI specification.
Since the function is optional, drop it.
Change-Id: I5f3a0810ac19ddeb3c0c5d35aeb09f09a0b80c1d
Signed-off-by: Samuel Holland <samuel@sholland.org>
The base address of UART peripheral should be given in R0, not in R1.
Otherwise the console_stm32_core_flush issues an assert message.
This issue was highlighted with recent changes in console flush functions.
Change-Id: Iead01986fdbbf30ad2fd9fa515a1d2b611b4e591
Signed-off-by: Yann Gautier <yann.gautier@st.com>
The issue is that, when interrupt is triggered and RAS handler
is entered, after interrupt handler finishes, TF-A will re-enter
bl32 and then crash.
sdei_dispatch_event() may return failing result in some cases,
for example kernel may not have registered a handler or RAS event
may happen early during boot. We restore the NS context when
sdei_dispatch_event() returns failing result.
error log :
Received delegated event
X0 : 0xC4000061
X1 : 0x0
X2 : 0x0
X3 : 0x0
Received event - 0xC4000061 on cpu 0
UnRecognized Event - 0xC4000061
Failed delegated event 0xC4000061, Status Invalid Parameter
Unhandled Exception in EL3.
x30 = 0x000000000401f700
x0 = 0xfffffffffffffffe
x1 = 0xfffffffffffffffe
x2 = 0x00000000600003c0
Signed-off-by: Ming Huang <huangming@linux.alibaba.com>
Change-Id: I9802e9a32eee0ac3b5a8bcc0362d0b0e3b71dc9f
Turn ON/OFF GIC redistributor in sync with GIC CPU interface ON/OFF.
Issue :
The Linux prompt hangs when all the cores in a cluster are turned OFF
and we try to turn ON a core in that cluster. Previously when TF-A turns
ON a core, TF-A first turns ON the redistributor followed by the core.
This did not match the flow when turning OFF a core, as TF-A did not
turn OFF redistributor when the corresponding core[s] are disabled.
This hang is resolved by disabling redistributor as cores are disabled,
keeping them in sync.
Signed-off-by: Jagadeesh Ujja <jagadeesh.ujja@arm.com>
Change-Id: Ifd04fdcfd47b45e00f874f15b098471883d023f0
Some switch cases uses same operation. So, club switch cases
which uses same operation and remove duplicate code.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I260b474c0ff3f2ca102c32d4af2e4abba2b8f57c
This allows PSCI in TF-A to signal platform power states to QEMU
via a controller in secure space.
This required a sbsa-ref specific version of PSCI functions for the
platform. Also adjusted the MMU range to also include the new EC.
Add a new MMU region for the embedded controller and increase the
size of xlat tables by one for the new region.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Change-Id: Iece8a88947f11e82ab8988e460a8a66ad175a5ee
sbsa-ref in QEMU creates clusers of 8 cores, it may create up to 512
cores in upto 64 clusters. Implement a qemu_sbsa specific topology file
and increase the BL31_SIZE to accommodate the bigger table sizes. Change
platform_def.h for new topology. Correct PLATFORM_CPU_PER_CLUSTER_SHIFT so
plat_helpers.S calculates correct result.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Change-Id: Idc5d70394c0956b759ad2c86f9fda8f293f2cfa7
DEVICE2 is not currently used on qemu platform but is needed for
a future patch for qemu_sbsa platform. Change its definition to
RW and add it to all levels of arm-tf similar to DEVICE1 definition.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Change-Id: I03495471bfd423b61ad44ec4953fb25f76aa54bf
Rather than re-create this file in multiple qemu variants instead
caclulate the shift needed to convert MPIDR to position.
Add a new PLATFORM_CPU_PER_CLUSTER_SHIFT define in platform_def.h
for both qemu and qemu_sbsa to enable this calculation.
Signed-off-by: Graeme Gregory <graeme@nuviainc.com>
Change-Id: I0e3a86354aa716d95150a3a34b15287cd70c8fd2
When getting a stack protector canary value, check
if cpu supports FEAT_RNG and use that. Fallback to
old method of using a (hardcoded value ^ timer).
Signed-off-by: Tomas Pilar <tomas@nuviainc.com>
Change-Id: I8181acf8e31661d4cc82bc3a4078f8751909e725
Add DT node support for channel 0 where physical memory is split
between 32bit space and 64bit space.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I99a18dbb14cdb54100a836c16445242e430794e3
The HiHope RZ/G2M board from HopeRun consists of main board
(HopeRun HiHope RZ/G2M main board) and sub board(HopeRun
HiHope RZ/G2M sub board). The HiHope RZ/G2M sub board sits
below the HiHope RZ/G2M main board.
This patch adds the required board support to boot HopeRun HiHope
RZ/G2M board.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I3ed55aa4a2cc5c9d9cd6440e087bcd93186520c7
Include header ulcb_cpld.h in plat_pm.c only if RCAR_GEN3_ULCB
is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ie89223097c608265c50e32778e8df28feed82480
Move rcar plat code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I1001bea1a8a9232a03ddbf6931ca3c764ba1e181
Move plat aarch64 code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I66265e5e68bfcf5c3534965fb3549a145c782b47
Move DDR/QoS/PFC header files, so that the same code
can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I2cc0ceda8d05b6b8d95a69afdc233dc0d098e850
Move rpc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I04805d720d95b8edcc14e652f897fadc7f432197
Move avs driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I85d9fa8b6abf158ce2521f1696478f7c5339fc42
Move authentication driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I02592dfc714998bf89b9feaa78f685ae36be6f59
Move dma driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Idce2e2f4e098cfc17219f963373d20ebf74e5b7c
Move watch driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I235f2cde325a0feeadbfc4b7ee02e8b1186f7ea1
Move rom driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I399dfb5eff186db76d26fa9c54bea88bee66789c
Move delay driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I5e806bd0e0a0a4b436048513b7089db90ff9805f
Move console/scif driver code to common directory, so that the
same code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I0b15e4f4ffaaa99e77bcee32b1dad648eeadcd9b
Move pwrc driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I75d91a44d872fe2296b15c700efacd5721385363
Move io driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ic661e415c91a1fbfd5eee3bba86466037e51574b
Move eMMC driver code to common directory, so that the same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I7f3055709337327d1a1c9f563c14ad1626adb355
Move plat common sources to common directory, so that same
code can be re-used by both R-Car Gen3 and RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Id2b1822c97cc50e3febaffc2e5f42b4d53809a17
Create a common directory and move the header and assembly files
so that the common code can be used by both Renesas R-Car Gen3 and
RZ/G2 platforms.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ia9a563a1c3c9f8c6f0d3cb82622deb2e155d7f6c
This patch fixes checkpatch warnings and replaces TAB with
space after #define macros.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I11f65d494997cbf612376fb120c27ef0166cdd3a
Sort the header includes alphabetically, fix typos and drop unneeded TAB
and replace it with space
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: Ieff84434877f58ec26c8351611059ad4e11a4e28
Sort the header includes alphabetically and fix checkpatch warnings.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Change-Id: I08fd0d12ee1d8d61391e8afc33f8c67fcf70c4e5
This implements support for UEFI secure variable storage
using standalone MM framework on qemu_sbsa platform.
Non-secure shared memory between UEFI and standalone MM
is allocated at the top of DRAM.
DRAM size of qemu_sbsa varies depends on the QEMU parameter,
so the non-secure shared memory is allocated by trusted firmware
and passed the base address and size to UEFI through device tree
"/reserved-memory" node.
Change-Id: I367191f408eb9850b7ec7761ee346b014c539767
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Add ability to support PS and System reset after idling the APU,
by reading the restart scope from the PMU.
Signed-off-by: Will Wong <willw@xilinx.com>
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: I23c01725d8ebb71ad34be02ab204411b93620702
ATF is not checking PM version. Add version check in such
a way that it is compatible with current and newer version
of PM.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Change-Id: Ia095d118121e6f75e8d320e87d5e2018068fa079
The current configuration of CPU windows on Armada 37x0 with 4 GB DRAM
can only utilize 3.375 GB of memory. This is because there are only 5
configuration windows, configured as such (in hexadecimal, also showing
ranges not configurable by CPU windows):
0 - 80000000 | 2 GB | DDR | CPU window 0
80000000 - C0000000 | 1 GB | DDR | CPU window 1
C0000000 - D0000000 | 256 MB | DDR | CPU window 2
D0000000 - D2000000 | 32 MB | | Internal regs
empty space | | |
D8000000 - D8010000 | 64 KB | | CCI regs
empty space | | |
E0000000 - E8000000 | 128 MB | DDR | CPU window 3
E8000000 - F0000000 | 128 MB | PCIe | CPU window 4
empty space | | |
FFF00000 - end | 64 KB | | Boot ROM
This can be improved by taking into account that:
- CCI window can be moved (the base address is only hardcoded in TF-A;
U-Boot and Linux will not break with changing of this address)
- PCIe window can be moved (upstream U-Boot can change device-tree
ranges of PCIe if PCIe window is moved)
Change the layout after the Internal regs as such:
D2000000 - F2000000 | 512 MB | DDR | CPU window 3
F2000000 - FA000000 | 128 MB | PCIe | CPU window 4
empty space | | |
FE000000 - FE010000 | 64 KB | | CCI regs
empty space | | |
FFF00000 - end | 64 KB | | Boot ROM
(Note that CCI regs base address is moved from D8000000 to FE000000 in
all cases, not only for the configuration with 4 GB of DRAM. This is
because TF-A is built with this address as a constant, so we cannot
change this address at runtime only on some boards.)
This yields 3.75 GB of usable RAM.
Moreover U-Boot can theoretically reconfigure the PCIe window to DDR if
it discovers that no PCIe card is connected. This can add another 128 MB
of DRAM (resulting only in 128 MB of DRAM not being used).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Change-Id: I4ca1999f852f90055fac8b2c4f7e80275a13ad7e
Reference Design platform RD-Daniel-ConfigXLR has been renamed to
RD-V1-MC. Correspondingly, remove all uses of 'rddanielxlr' and replace
it with 'rdv1mc' where appropriate.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I5d91c69738397b19ced43949b4080c74678e604c
Reference Design platform RD-Daniel has been renamed to RD-V1.
Correspondingly, remove all uses of 'rddaniel' and replace it with
'rdv1' where appropriate.
Signed-off-by: Aditya Angadi <aditya.angadi@arm.com>
Change-Id: I1702bab39c501f8c0a09df131cb2394d54c83bcf
Ying-Chun Liu (PaulLiu)
Masahisa Kojima
Dawei Chien
Julius Werner
Marek Vasut
Toshiyuki Ogasahara
André Przywara
Madhukar Pappireddy
Mark Dykes
Marek Behún
Lionel Debieve
Saurabh Gorecha
Olivier Deprez
Usama Arif
Yann Gautier
Balint Dobszay
Manish V Badarkhe
Jiafei Pan
Marcin Wojtas
Joanna Farley
Icenowy Zheng
Vijayenthiran Subramaniam
Pali Rohár
Ronak Jain
lwpDarren
johpow01
Tom Cosgrove
Varun Wadekar
Manish Pandey
Abdellatif El Khlifi
Venkatesh Yadav Abbarapu
Rex-BC Chen
J-Alves
Stas Sergeev
Jeremy Linton
Arunachalam Ganapathy
Samuel Holland
Maksims Svecovs
Roger Lu
Garmin Chang
Jimmy Brisson
Yann Gautier
Abhyuday Godhasara
Ruchika Gupta
Sandrine Bailleux
Edward-JW Yang
Elly Chiang
Tinghan Shen
Daniel Boulby
Patrick Delaunay
Patrick Georgi
Nicolas Le Bayon
Igor Opaniuk
Michal Simek
Peng Fan
Vyacheslav Yurkov
Jan Kiszka
Manoj Kumar
Jiaxin Yu
Pranav Madhu
Hsin-Hsiung Wang
Flora Fu
Rex-BC Chen
Rajan Vaja
Zelalem
Davidson K
Jacky Bai
David Horstmann
Aditya Angadi
Yidi Lin
mtk20895
James Liao
gtk_pangao
christine.zhu
Shubhrajyoti Datta
bipin.ravi
Lad Prabhakar
Mikael Olsson
Konstantin Porotchkin
Alex Evraev
Guo Yi
Grzegorz Jaszczyk
Alex Leibovich
Nina Wu
Leif Lindholm
Heyi Guo
Omkar Anand Kulkarni
Thomas Abraham
Bharat Gooty
Nishanth Menon
Pankaj Gupta
Tejas Patel
Heiko Stuebner
Xi Chen
Maxim Uvarov
Lauren Wehrmeister
Avinash Mehta
Ming Huang
Jagadeesh Ujja
Graeme Gregory
Tomas Pilar
Biju Das
Will Wong